Jump to content
SAU Community

FS: Volk Racing Rays Challenge Rays Engineering Wheels

R1Titan
 Share

Recommended Posts

R1Titan Collaborator

R1Titan

Posted
Posted

For Sale-

F: 17 x 8.0 JJ +32 PCD 114.3 x 5 stud

R: 17 x 9.0 JJ +35

Volk Racing Challenge

Rays Engineering in WHITE with inner BLUE trim

$2200 without tyres

$2700 with tyres

Fronts: Toyo Trampio Gu:wn 235/45/17 (50% thread)

Rears: Dunlop Formula FM901s 255/40/17 (85% thread)

Make me an offer for these rare and imported rims.

----------------------------------------

PRICE DROP:

$2000 without tyres

$2300 with tyres

-----------------------------------------

DVC00064.JPGPRICE DROP: $2000 without tyres $2300 with tyres

R1Titan Collaborator

R1Titan

Posted
  • Author
Posted

R33gtst: Those are the wheel offsets. It should fit any R33 Skyline no problem

russcb007: no pm was received? try again?

rs73: yup s15. The wheels don't stick out but I will need to roll/lip the guards should i lower the car. However, the R33 has wider guards then the s15

Still 4 sale!!!!

  • 2 weeks later...
ice180 Mentor

ice180

Posted
Posted

I'm still trying to get some rims from Canberra but guy is stuffing me around plus at 19 inch think they are too big. Love yours and am keen but means I have to convert to five stud as they are for a 180 which means more expense.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • GTSBoy
      Another "where do these lines and plugs go" RB25DET question

      By GTSBoy · Posted

      4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • GTSBoy
      R34 GTR Seats / No longer reclining

      By GTSBoy · Posted

      Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...