Jump to content
SAU Community

Recommended Posts

More than likely not

But in theory it should due to some of the air running back into the engine and not getting dumped into the atmosphere?

Ill play with this and get back. This whole "pshhht sick uleh" shit is bit annoying considering the car is not as reliable as its with a stock bov.

GFB hybrid was installed on my car for years, no issues with stalling from it, full atmo was swapped and i had that issue.. it will be better than a full atmo.

So no stalling at all on 50 50? Cos I been driving with it for a few days now and it stalled completely once when I was idling... and then also had these small "set backs" like when I pushed the throttle and it just stalled for half a sec then let go and was fine again... this really pisses me off.

Edited by Sir-D
no stalling at all related to the 50,50 setup i had.

each car is different though, they are worse than people sometimes lol

thanks dude... ill give it a go this week.

PS love the pod suction noise and flutter... did u lose any of that? how did she sound on 50 50?

i've got a stealthfx .. on about 60/40 cos i don't want it too loud .. i have no stalling issues whatsoever . .even if i put in the clutch and let the revs fall.

if you are getting stalling, adjust the spring tension by twisting the cap only. that will make the bov close sooner and should get rid of your stalling issues.

Was it the stealth fx BOV??

I so want that bov.. Best soundin one i have heard..

What does your sounds like on just plumback??

no its GFB Hybrid... u can have 50 atmo 50 plumback setting.

my mate has Stealth FX on his s15... it sounds the best like u said... the flutter down low and awesome water splash when giving it!

well the flutter on a skyline is compressor surge not such a good thing to have if you value the life of the turbo. the 50/50 set up should be fine.

yeah its the BOV fluttering and it says that its OK for flutter at low RPM in the booklet.

at high rpm it whistles!

also look at VL turbos... they have no bov... and their turbos seemed to last for years.

I still get a flutter (gfb hybrid on 50/50) noise on low boost but thats coming from the bov it self as piston slides up and down.

When i took the bov off it fluttered in a different way.

u just connect the hose to the plumback trumpet right and vent the atmo plug yeh?

stealth_skyline_feature_sml.jpg

one pointing towrds you and is round, put hose over that to the std plumb back piping..

the other is a trumpet and you leave it alone.

just have to swivel the bov on the adapter so its in the right position..

edit : use hose clamps

Edited by Craved

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hell, I'm sufficiently wary of the ZSS suspension arms, let alone something like a hub.
    • Got it back home and got started pulling the hub off and diagnose the issue. Axle was stuck after removing the 36mm nut so i used a 3 jaw puller to try and push it out and... eH5FXvJ8.mp4   spend the next few hours trying to remove the axle from the remaining hub as it was very much jammed in there when the spindle sheared off. resulting damage as below R53AIy6 - Imgur.mp4   Looks like the was already a stress fracturing in the spindle as can be seen with the darker cracked section My working theory is maybe when the pinion gear exploded last year the shock put through the hub was the initial crack. Then a few events later it finally let go. Just lucky it happened where it did and not 190km/h on the next sweeper or into the hairpin The bearing/hub assembly went in in 2019 and were non-genuine "ZSS" assemblies and no nails were harmed in the process. #BreakHubsNotNails
    • Thanks mate, couldn't find in VIC, ended up ordering one from NSW, getting rwc to get new plates and registration done.
    • Before all the EFR fan boys come in, have a look at: https://www.garrettmotion.com/racing-and-performance/performance-catalog/turbo/g-series-ii-g30-825-58mm/ It also comes in a T4 1.06 divided housing. I would dare say if you want response & also decent power, this thing would chop.   AND apologies, just re-read your post, you've already bought the turbo... whatever you do, make sure you stick with divided housing and proper twin scroll manifold.
    • People have got to stop doing that. ShatGPT is not a search engine. It is a hallucination factory.   I also would recommend the 1.05. The .83 will "work" for you , in that it will be more responsive, but I think you'll find that it won't be anywhere near as good running it out to 8000rpm as the big housing will be.
×
×
  • Create New...