Jump to content
SAU Community

Recommended Posts

  • Replies 240
  • Created
  • Last Reply

Top Posters In This Topic

best thing for you to do mona if all you want is 250 KW is just buy a bare motor and put your bolt ons on it.

Otherwise if you do want more power

$$$$$

depends what you wanna use the car for in the end

Im selling my car cause ive got a new project comming

aiming for the 800Kw mark and in the mid 8 second passes.no point in wasting my car just sell it and start fresh

Interesting. Buster's right. They all have their place and not just from a performance perspective. There are other things to consider. I looked at the rebuild NEO or go RB30 thing recently when mine blew and decided that the rebuild suited me best. I'm happy with my choice and enjoying it.

from what it seems its overly sensitive. this can happen from having the sensor to tight.

the pistons are perfect. not a whisper of detonation

I got this problem with my 3 litre.. it allways knocks on the PFC but we can never hear it at all!!!

I took it to many dyno's and they tuned it with knock levels of around 100 yet there was no detonation because we could not hear it at all.

They told me to ignore the knock level because its not knocking.

My knock sensors used to work ok till the 3 litre went in to maybe we tightend them up too hard ??? how do you know when its in too hard ??? how to you get it right ?

Edited by Guilt-Toy
I got this problem with my 3 litre.. it allways knocks on the PFC but we can never hear it at all!!!

I took it to many dyno's and they tuned it with knock levels of around 100 yet there was detonation because we could not hear it at all.

They told me to ignore the knock level because its not knocking.

My knock sensors used to work ok till the 3 litre went in to maybe we tightend them up too hard ??? how do you know when its in too hard ??? how to you get it right ?

from memory its 15nm. with a lubricated thread. so yeah. just nipped up

basicly the same tension as the ignition coil holders.(the 12mm bolts)

from memory its 15nm. with a lubricated thread. so yeah. just nipped up

basicly the same tension as the ignition coil holders.(the 12mm bolts)

I did not even know about the coil holders not needing to be in tight lol

Got any other usefull information for us ? =)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
    • You think its the AFM? I know its a common issues on R32s. I find it coincidental how this issue raised right after cleaning the fuel system. As everything except the fuel system was fine before. I tried running it with the IACV unplugged but did not notice a difference and still stalled. However, the RPM gauge is not in the cluster right now, so I will need to connect the laptop again and use Nistune to check the RPM. I will check this weekend.
×
×
  • Create New...