Jump to content
SAU Community

Recommended Posts

Hey all,

I'm wondering if this is a normal thing to r32gtsts. This is what happened to me tonight. Pretty interesting experience to say the least. Hopefully not too Expensive to fix to get it back on the road.

I was casually driving to dinner tonight and I noticed the revs were a lot higher than normal on idle. Also when I used the throttle it was reving a lot higher than before (to get to the same speed I had to rev it a lot higher). Also the car fully died a few times when I was clutch coasting (i.e When i was turning a corner and slowed down to 2nd gear and put the clutch in, it died and I had to restart the car quick smart). So something felt strange but I didn't want it, to spoil the night so I kept going.

The recent things I have done to the car is flush out coolant and brake fluid 3 weeks ago. Changed engine oil, oil filter and fuel filter a week ago.

As I was parking the car something burst under the bonnet and I can see steam coming out. I popped the bonnet up and I see all this liquid everywhere. It was green and the coolant level was low so obviously it was the coolant.

We went out for dinner and came back and I tried starting up the car and it was fine. So I drove off but I took it real slowly as I knew something was not right. On the highway the car after about 15 mins of driving the car stalled. I tried to start it back up but it wouldnt (similar situation as if u had a flat battery) and I saw steam coming out again - no explosion this time though.

Some of you would already know what 'actually' happened - yes there was a crack in my radiator piping (picture attached).

Thankfully the car was towed back home and is safe and sound. I'm just wondering what options I have from here. Can I just replace this top plastic section (with the crack) or do I have to replace the whole radiator system?

If anyone has had the same experience before and can give some rough prices to fix it, it would be greatly appreciated.

Also can anyone pinpoint what could have caused this burst. Is it just old age and being a plastic pipe? Or I wonder if I had anything to do with the coolant flush that I got the mechs to do?

I guess it could have been worse :angry:

post-24116-1145971727.jpg

post-24116-1146281706.jpg

Edited by Andyn
Link to comment
https://www.sau.com.au/forums/topic/114933-not-my-day-today/
Share on other sites

You need to buy a new/second hand radiator all together.

Because once they have cracked, it means the whole thing is pretty brittle.

Didn't you notice that the car was overheating? usually they stall if too hot, but you should have seen the temperature go up quick.

This can also damage the head. Make sure u get that checked out as well!

Good luck, shouldn't be too expensive, i'm guessing cost of radiator + coolant + labour is you'll have to pay, assuming your head is still good.

Edited by IOWNU

Ok is this a normal thing for it to crack for no reason? I wonder if it has something to do with the coolant flush/pressure test, which i did 3 weeks ago?

No i didnt notice the engine temp being higher than normal...

Im hoping it didn't damage the head - but if it did - theres not much I can do about it apart from rebuild. Touch wood.

Ok is this a normal thing for it to crack for no reason? I wonder if it has something to do with the coolant flush/pressure test, which i did 3 weeks ago?

No i didnt notice the engine temp being higher than normal...

Im hoping it didn't damage the head - but if it did - theres not much I can do about it apart from rebuild. Touch wood.

It's normal with age, they get brittle, bang.

You didn't drive it too much so its ok, its unlikely the head is gone, but still a possibility.

Check if there is oil mixed in water in your radiator/overflow bottle. If yes, then we have a problem.

the flush just mighta been what caused the radiator to crack. i flushed mine and about a week later a crack went down the side and i needed a new radiator. tho i do think it was the original one so it did have a fair stretch on it...

Yeh coolant looks fine and no sign of oil.

Actually i was reading a thread and there was this:

"1. Turn the ignition on and set the climate control to max heat (32 degrees). The R32 GT-R workshop manual actually says to "remove the external sensor connector" once the ignition is on, but later manuals (for R33/34) say just to set the heater to max (which is what I did). Apparently this is meant to release any fluid in the heater."

I remembered that this morning I did tape up the temperature sensor thats plugged on the middle dash of the car (see picture). Could this have been the culprit? My climate control has been playing silly buggers - reporting higher than actual temps. When the air con is off I can still feel some 'cool' air from the left side of the drivers footwells.

post-24116-1145974352.jpg

Edited by Andyn

You have done the crack in wat is called the top.

I got a hole in that aswell not in my skyline but in the car i previously had. I took the radiator out n just took it to a radiator place n they put a new top tank on it. It didnt cost much mabey $120 or something. I dont know if the skylines ones are fixable or wether its better to just get a whole new radiator but if u dont want to replace the radiator just call a radiator place n they will be able to tell u want to do.

If its just the top tank that has been cracked, then that is what they will replace. you can go for a whole new radiator though. the top tank is most prone to getting small cracks and the like as this is the warmest part of the radiator. If you noticed that coolant was bursting out of your car, you shouldnt have been driving it, even if you were only just driving slow. The last thing you want is to damage your engine.

it was in my commo so it wasnt that expensive. $140 for a new radiator and it installed it myself. i was quoted $80 i think for my mechanic to do it and replace the coolant.

its fairly easy in a commodore not sure about a skyline tho. in a commodore it take of radiator cap, unto bottom hose into bucket and let it drain. remove all hoses (auto too so auto line went into it too). take of fan shroud and slide out old radiator. then do the reverse...

how much is a stock radiator for a skyline. i wanted to upgrade mine by was advised against it by a few in the know as stock radiators are pretty good unless youve got a big huge powerful engine.

my radiator wasnt really repairable. it wasnt that much of a crack but iy was pushed out... id rather have a good condition something than one thats busted and been repaired...

I gather you are looking for two things;

1. The reason why it happened?

My guess is you didn't bleed the air out of the radiator and engine after you flushed it. Hence the engine built up pockets of trapped air. These produce hot spots in the engine that boil the water around it. The increased pressure from the boiling water cracked the radiator at the weakest point.

Did you bleed the radiator and theengien aftger you refilled it? Using the bleed on the top of the inlet manifold?

Although why the radiator cap didn't relieve the pressure is interesting. Did you change the radiator cap when you did the flush?

2. How to fix it?

The top tank is actually clipped/clamped on, they are rather difficult to repair after 13-17 years of use. My suggestion would be to buy a replacement radiator.

:worship: Cheers :D

As soon as you fit the new radiator I would do pressure test as I would be surprised if you haven't warped the cylinder head from the excessive localised hot spots.

Edited by Sydneykid

QUOTE: The top tank is actually clipped/clamped on, they are rather difficult to repair after 13-17 years of use. My suggestion would be to buy a replacement radiator

They dont fix the top tank if it has a crack, hole or split in it. They REPLACE it. Ive seen it done mate. Dont worry about buying radiator. Once the top tank is replaced you wont have to worry about it for the next many years to come. Just worry about the bottom one lol. The tank may cost you about 120 bucks, then all up about 180 including the labour. I had the top tank replaced on my 180sx a few months back. The radiator comes in about three pieces. the top tank, the core and the bottom tank.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...