Jump to content
SAU Community

R32 Gtr Diff Q's

gashley
 Share

Recommended Posts

gashley Apprentice

gashley

Posted
Posted (edited)

hi everyone!

might be about to buy a rear subframe off a 32gtr to fit to my 180sx. the guy that i'm buying it off says the standard 32gtr's have a 2way mech diff.... is this correct???

also do you guys think it's worth it??? he wants $750 for the whole thing(half shafts, diff, subframe, rotors, calipers and hubs)

cheers guys,

ash. :P

Edited by gashley
Link to comment
https://www.sau.com.au/forums/topic/115073-r32-gtr-diff-qs/
Share on other sites
SteveL Mentor

SteveL

Posted
Posted
Sorry Duncan but an R200 is the standard GTS-t viscous diff and it is certainly NOT a 2-way... GTR diffs (R220) were only one way.

cheers

I don't know where you get your info, but Duncan is correct, R32 GTR uses R200 diff and the standard LSD centre is mechanical (ie clutch pack). I've had the one out of my GTR, plus inspected the centre and it's 2-way (most definately stock - believe me I've seen the inside of more than 1 or 2....)

R32 GTSt also uses R200, but has a viscous LSD.

I've never heard of such a thing as an 'R220' diff used in any Nissan, but there is an R230 type that is used in Z32 turbo.

Link to comment
https://www.sau.com.au/forums/topic/115073-r32-gtr-diff-qs/#findComment-2137535
Share on other sites
SteveL Mentor

SteveL

Posted
Posted
Seems there is some confusion here. My GTR certainly has a tight rear mech LSD, looks factory.... but are they 200 or 220? And 2way, 1way, or 1.5?

There's no confusion about the diff type.....R200. No such thing as an 'R220' AFAIC.

The factory GTR WS manual lists the rear diff as R200 and FAST confirms as well.

Also AFAIC the factory R32 GTR LSD centre is 2 way.

Link to comment
https://www.sau.com.au/forums/topic/115073-r32-gtr-diff-qs/#findComment-2137681
Share on other sites
Erelyes Apprentice

Erelyes

Posted
Posted
There's no confusion about the diff type.....R200. No such thing as an 'R220' AFAIC.

The factory GTR WS manual lists the rear diff as R200 and FAST confirms as well.

Also AFAIC the factory R32 GTR LSD centre is 2 way.

Yeah. No confusion. Did you not read the contradicting posts at the start of the thread. :O

That said, thanks for providing a SOURCE of info confirming it (w/s manual).

Now, can anyone tell me what TYPE of mechanical diff it is - 2-way, 1-way, or 1.5-way. I know (well, I've read on here) that it is helical, but that's it.

Link to comment
https://www.sau.com.au/forums/topic/115073-r32-gtr-diff-qs/#findComment-2141460
Share on other sites
T04GTR Grand Master

T04GTR

Posted
Posted

OMG WTF FLAMES LOL. im jelouse.

to fit the diff/subframe.

swap the diff flange from the 180sx diff.(i hpoe its a non abs 180)

unbolt the subframe. bolt the new one up,happy days.

you will have to use r32gtr rear suspension as the lower mounting is differant., but thats pretty much it.

a very straight forward conversion :O

(r200) 2 way mechanical lsd,,,not very tight,

R220=220MM crownwheel (RD) (Z32 TT)

r200=200mm crownwheel (RC)

r180=180mm crownwheel (RB)

r160=160mm crownwheel (RA)

Link to comment
https://www.sau.com.au/forums/topic/115073-r32-gtr-diff-qs/#findComment-2141542
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ToothDR32
      $5 Clock upgrade for R32 GTR

      By ToothDR32 · Posted

      Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...