Jump to content
SAU Community

Recommended Posts

Hi all,

Just took these off my GT-R. They were sold to me as HKS manifolds but my mechanic doubts they are HKS, he does think they are Japanese though and he thinks they must flow great as they're a lot bigger and better than the stock steel manifolds.

I want $300 ono for them, the catch is that they have been strengthened before (I paid someone to do it) and yet I have found a hairline fracture on one of them. So SOLD AS IS, thus, cheap cheap cheap! You will have to get them repaired before fitting them on to your car.

They are bolt on, direct replacements for stock RB26 manifolds. In Sydney, pick-up or can send too.

Pics:

manifold_01.jpg

manifold_02.jpg

manifold_03.jpg

Link to comment
https://www.sau.com.au/forums/topic/115138-hks-manifolds-for-rb26/
Share on other sites

Hi Justin, just to confirm your suspicions (sp*) they are not HKS manifolds.....But cracks like that can be easily tigged up by a competant fabricator, as long as they turn down the current at the end of the weld as to not burn a hole through them.

Edited by DiRTgarage
  • 3 months later...

SO MANY PM's!!!

Yes $100 for the both.

They are at:

http://www.jdmyard.com

I've left them there with Zi and Yonas to make it easy for you guys to check them out. Check the site for phone numbers (to check if they are open) and also address/map details.

Guys,

These were picked up for me by a mate, who didnt realise im doing a single turbo conversion. So i now have them for sale, same price, just come and take them :D

PM me or reply in this thread

Steve

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...