Jump to content
SAU Community

Recommended Posts

I need help .... i need to know what needs to be done to my car before i put a better turbo on my car. I have a front mount 3 inch turbo back zorst and pod. everything else is stock. im interested in putting a better turbo,

also i need to know what turbo to get i dont want to spend big bux and dont want huge power. i know of a few people putting highflowed 33 or 34 turbos on there r32's. are these reasonable turbos i should look for.

What i am looking for is a little bit more power but most of all relyability.

thanks for your help

sorry i dont know much ..

Link to comment
https://www.sau.com.au/forums/topic/117480-better-turbo-for-r32-gtst/
Share on other sites

based on my experience, anything more than the stock turbo requires a fuel pump

i can recommend an rb25 turbo and the only extra thing you will need is a fuel pump (as mentioned) and that will work with the stock ecu nicely

this will also maintain reliability

you might want to also consider a boost controller..

cheers,

Warren

R34 turbo would be better again, but a lot harder to come by and more expensive.

If you go and R33 turbo, you want to get it from a series 2 as they have a nylon compressor wheel and are rated at 180-190 odd rwkw.

I have an R34 turbo on the way for mine, can't wait!

I have a bosch 040 fuel pump and a remapped ECU, I also have 3" dump back, POD filter, EBC and front mount... will get it retuned once I fit my GTR injectors and Z32 AFM.

R34 turbo would be better again, but a lot harder to come by and more expensive.

If you go and R33 turbo, you want to get it from a series 2 as they have a nylon compressor wheel and are rated at 180-190 odd rwkw.

I have an R34 turbo on the way for mine, can't wait!

I have a bosch 040 fuel pump and a remapped ECU, I also have 3" dump back, POD filter, EBC and front mount... will get it retuned once I fit my GTR injectors and Z32 AFM.

What rw/kw you expecting with that type of set up and if you dont mind me asking what would it roughly cost.

What rw/kw you expecting with that type of set up and if you dont mind me asking what would it roughly cost.

I managed to get mine for $530 shipped... But I have been looking for about 6 months!

I am aiming for a very responsive 200rwkw! Should be quite acheveable, just got replace the dump and cat I rekon.

Edited by CATKICKER

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
    • I _think_ that one has a christmas tree or some other retainer spike into a hole in that panel under it. Come in under it with thin scredrivers and just pry it gently up. If you rip the ears off the retainer pin....so what? Just stick it back down after with a bit of race tape and carry on with life.
×
×
  • Create New...