Jump to content
SAU Community

Friday Nite Calder Drags

sssrama

By sssrama,
in Victoria

 Share

Recommended Posts

KURAUN Grand Master

KURAUN

Posted
Posted

Yeh I saw it and its not ment to drag race its from G-Tech and the car has balls its a handful i see him come down the street near my work an i bet most peoplke would have a hard time driving it as when it hits boost its all over the road. I was surprised on his first coupling attemps that he was not all over the strip, in my books he is a skilled driver to keep that thing straight

Interloper Veteran

Interloper

Posted
Posted
I just got back from heathcote. Ran my GTR. Only 2 runs.

First 13.3@108mph, Second 12.8@06mph

Car is stock, besides catback exhaust & hks air filters

how come you only got 2 runs? were there heaps of cars running?

normally should get alot more than that!

Russman Grand Master

Russman

Posted
Posted
i cant wait to get mine down there bit of a hike 6 hrs but i think it will be well worth it wanna run a got time with all the work done to it

Is there a 1/8 mile track in Mildura?

I remember my first attempt at calder. Pretty intimidating. Racing a 12sec 1930s hotrod, open exhausts. couldn't hear my engine. could only took at the tacho to see if it was still running!

allblitz Grand Master

allblitz

Posted
Posted
how come you only got 2 runs? were there heaps of cars running?

normally should get alot more than that!

Actually, there were only around 8-10 cars racing :D I didnt see a need to race anymore, 12.8 is pretty much the best the car can do with stock boost, and just catback exhaust. No need to stress it out anymore in my opinion.

teazn_r33 Mentor

teazn_r33

Posted
Posted

yer there a 1/8 mile but i waana run a 1/4 time and as mildura is a small town word gets round quick n ppl talk shyt nut im guessing that there aint mush diffrent were ever you go buy the look of things just cause you have a bad day at the drags ppl on your case

Roy Grand Master

Roy

Posted
Posted
Is there a 1/8 mile track in Mildura?

I remember my first attempt at calder. Pretty intimidating. Racing a 12sec 1930s hotrod, open exhausts. couldn't hear my engine. could only took at the tacho to see if it was still running!

Nothing to be intinidate about...just let this noisy bloody things hammer off down the track while you sit there and listen to your tunes...When they have cleared the 60ft then let it rip. The noise thing from open ended pipes and V8s makes it hard. But i find you forget there are ppl around when you start to concentrate. You almost zone out

dezz Grand Master

dezz

Posted
Posted

my first ever run was a against a 33 GTR that almost broke into 11's....12.1 or 12.2 i beleive he ran...

i honestly paid no attention to what he was doing, and im certain he paid no attention to me...everyones there to beat their own time, and rarely racing the car next to them....dont be intimidated...sure i was nervous for my first run, but once i hit the finish line, i couldnt wait to run again!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...