Jump to content
SAU Community

Recommended Posts

Hi there guys im about to purchase another R34-4dr...I was just wondering has anyone else seen another sort of kit that has been fitted on a 4door? either than URAS or NISMO and has anyone have any recommendation where i can purchase a kit from??

Thanks in advance

Edited by r34-4dr
Link to comment
https://www.sau.com.au/forums/topic/117791-r34-four-door-body-kits/
Share on other sites

  • 2 years later...

aii bro i got a four door n i been realli lookin into 4 door body kits and to tell u the truh my fave would hav to be the east bear 4 door kits..they got sum sik 4 door gtr kits and heapz of shit for four doors so i rekon u chek em out...there a japanese brand but i thnk sum places provide a small range of there kitz in syd frm wat ive seen...but i havent seen the 4door nismo kit for da skyline u rekon u cud email us da pics at [email protected]

4 door luv =P

Def normal, im budgeting over $1000 for the bodykit alone (front, side, rear, and spoiler), and $500 for a paint is a good price.

Something a bit special like a full crossfactory or eastbear kit could be getting up over $2000 easy, without painting

Even a cheaper kit from Carmate et al. are gonna be $300 front, $300 sides, $300 rear, maybe a little discount if you buy all at the same time...Still $900

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...