Jump to content
SAU Community

Recommended Posts

it is a 1989 r32 gtr Gunmetal Grey with 96xxxkms on the clock and a few mods ,hks air filters,18inch mags with near new tyres ,strut brace ,gready turbo

timer, ,sony mp3 head unit .the car is in very good nic and just had a big service done about 4 to 5 mouths ago which included all the belts eg gates timing belt ect ,all the oils ,coolant spark plugs, was also replaced every thing that is needed to be done for the 100k service I got done then .also at that time I got the water

Pump replaced.also had a new clucth put in 3 weeks ago and i dont drive it to much only like 4 times a mouth on weekends.and it is always keep in a carport and looked

After and is good for its age,also I will give with the sale of the car a n1 front bar

And rear pods wich will have to be painted as I haven’t got around to getting that Done .

now whats wrong with it the rear turbo has blowen other than that the car is fine the front turbo is fine but i need to sell it has i need a car to drive to work and it is to hard to get a bus ,train ect to work so i need to sell it fast.

i am asking $15,000 neg or near that .open to offers .

feel free to call me on 0410727690

Edited by gtr2env
  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

if you need photos plase give me your email address to day cos

i cant email cos most of the weekend i wont be home ,il be at

my gfs house but if you wont to look at the car jst give me a buzz and i

can work something out cos my gfs live about 20mins from my

house.

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...