Jump to content
SAU Community

Recommended Posts

Hey guys, I did a quick search, but didn't find anything too helpful. My driver's side window switch is stuffed, and i can't put the window down without jiggling and forcing the button. Even then it rarely works.

Once the window is down, the switch works fine, i can raise it fully or to a selected height, but not back down again. Passenger side - no problems.

This is driving me crazy! I had my mechanic look at it, he said he sprayed it with some solution that is very good for cleaning contact points, but no luck.

I don't particularly want to fork out the $200 the wreckers wanted for a second hand unit. Anybody got any ideas? or a spare unit for sale?

Any help would be much appreciated!

Cheers

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/
Share on other sites

Hey guys, I did a quick search, but didn't find anything too helpful. My driver's side window switch is stuffed, and i can't put the window down without jiggling and forcing the button. Even then it rarely works.

Once the window is down, the switch works fine, i can raise it fully or to a selected height, but not back down again. Passenger side - no problems.

This is driving me crazy! I had my mechanic look at it, he said he sprayed it with some solution that is very good for cleaning contact points, but no luck.

I don't particularly want to fork out the $200 the wreckers wanted for a second hand unit. Anybody got any ideas? or a spare unit for sale?

Any help would be much appreciated!

Cheers

Take it to an electrician ASAP- mine only went downhill from there. Now it's stick about an inch down. Does anyone know if there's a way to manually raise it?

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2189700
Share on other sites

Check the For Sale section for people wrecking their cars - thats where I got my power window switch unit.

Replace it asap as mine was like that and one day the switch got stuck in the down position (although it looked in the neutral position) and this caused the motor to wear out and die.

In short - this made me have to replace the switch unit as well as the power window motor - not cheap at all.

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2189852
Share on other sites

Try attempting to put your window up/down with your head close to the inside of the door. If you can hear a click sort of noise near your right elbow when you press the button, the button is ok. I have this problem with my series 1, I can sometimes get my window to go up or down, but when it doesn't, i can still hear a little click (the power works). My problem is that the contacts in the motor are a bit funny. I've pulled the door apart and looked at the motor and it's ok, but doesn't work when the axle is pushed in.

So in other words, Clicking noise = motor problem

no clicking = probably switches are buggered.

hope this helps.

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2191624
Share on other sites

WHAT STATE R U IN BRO CAUSE IF U LIVE IN SYD I CAN GET I WINDOW MODULE FOR U CHEAP

I'm in Melbourne mate. Can you please PM me a price?

I've found that if i hold the button up (while window is up) then quickly press down quite firmly it works, but i can't be stuffed doing that EVERY time. Makes me think it must be the contact points.

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2193282
Share on other sites

I'm in Melbourne mate. Can you please PM me a price?

I've found that if i hold the button up (while window is up) then quickly press down quite firmly it works, but i can't be stuffed doing that EVERY time. Makes me think it must be the contact points.

about 130 bucks bro if u want email me and we will sort something out bro

my email address is [email protected]

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2199032
Share on other sites

In my series1 R33 my window froze is the down position...

Had to get a new window regulator and motor, brand new the prices (with installation) would have been close to $1000, i used second hand parts and cost as $600 - $650...

And still my window wont go up and down when i want it to, have to continue to move the switch until it decides to come up....

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2214242
Share on other sites

In my series1 R33 my window froze is the down position...

Had to get a new window regulator and motor, brand new the prices (with installation) would have been close to $1000, i used second hand parts and cost as $600 - $650...

And still my window wont go up and down when i want it to, have to continue to move the switch until it decides to come up....

Swapped the switch box?

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2214465
Share on other sites

you guys are all slack'as

take the switch out, pull it apart

you'll find a nice big carbon build up on the buttons connection points...

grab some fine sand paper and some electrical contact cleaner and clean those connections

windows will work after this :dry:

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2214875
Share on other sites

you guys are all slack'as

take the switch out, pull it apart

you'll find a nice big carbon build up on the buttons connection points...

grab some fine sand paper and some electrical contact cleaner and clean those connections

windows will work after this :(

Have you actually tried this?

I couldn't open my switch box (even after I unscrewed all the visible screws) when I tried.

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2215421
Share on other sites

yes.. i did it yesterday

window works perfectly now

undo all screws

then get small flat head screw driver and prise open switch (has small clips on the side of switch box

depending on the age/condition of the car.. the solder on the circuit board might have corroded and you may need to un-solder and resolder all the wires back in.. however 90% of the time.. its carbon build up on the contacts of the switches that stops connection between the contacts and the circuit board.. hence why windows not budging.. or only occasional movement when switched are violently applied

you need to take the whole thing apart.. and sand all the carbon build up off the connection points

works awesome after that :wave:

-Ruffels

(credit goes to foznice who showed me how to fix this problem)

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2215584
Share on other sites

  • 3 weeks later...

Which bit's the regulator? is it the little black box that the switch wires plug into, or is it further inside the door? i thought it was the box, but when a mechanic friend looked at it, he said something further into the door was the reg, and that it had it's own motor which was stuffed.

Link to comment
https://www.sau.com.au/forums/topic/118865-window-rooted/#findComment-2280994
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...