Jump to content
SAU Community

Recommended Posts

Does any body know if a rough idle can be caused by leaking intercooler pipes. Because my 32 is idle ing up n down between 500-2000 on and off. and if u hold it on around 2500 it has a miss occasionally. Can stale fuel cause this also as my car has been sitting for the last 3 months. any held wuld be great.

Link to comment
https://www.sau.com.au/forums/topic/118959-rough-idle-intercooler-leak/
Share on other sites

Does it ever stall out on you at lights or pulling up somewhere and stopping?

or just rough idle?

i think there is a diy article on how to reset your computer idle and base idle, there are 2 different settings if im not mistaken.

cheers mate

if it idles like that how does it drive when you accelerate?

is it drivable?

does it rev out and boost properly?

I jsut recently had a problem where the car would cut out.

nd occasionally rev between 500 - 2000 rpm.

my issue turned out to be a dirty air flow meter.

I took the AFM off the car (1 plug 1 clamp and 4 bolts) and sprayed the inside of the AFm with degreaser then washed it out.

shook it dry then dried it out properly with a hair dryer.

now it workds great, idles better than it ever did and revs out clean.

it is also smoother to drive.

might be worth a check if you havn't already done so

Could be the case of a stuffed BOV..

is yours the stock one? or some aftermarket vented BOV?

If its an aftermarket one, it could have ceased up and letting air come into the motor before the AFM gets to read it when your idling hence causing the car to stall

Edited by johnnilicte

or if your bov is the stock one and you have vented it to atmo then it could be leaking. we took the plumb back hose of my mates 33 on the weekend and it wouldn't idle unless we put our hand over the bov to stop it leaking. and mine does the same thing. we plug up the plumb back hose and it won't idle unless we plug up the bov as well cause it was leaking like a $2 hooker. both bovs dump ok and don't leak boost under revs but they leak at idle when not plumbed back. any ideas why?

i'm looking at upgrading it to an aftermarket plumb back.

Edited by mad082
Does any body know if a rough idle can be caused by leaking intercooler pipes. Because my 32 is idle ing up n down between 500-2000 on and off. and if u hold it on around 2500 it has a miss occasionally. Can stale fuel cause this also as my car has been sitting for the last 3 months. any held wuld be great.

Mine did this after I got it back from a respray. They had it for 3months and it apparently hadn't been started the whole time, simply pushed around.

Mine idled like crap, blew lots of black smoke and had to be held up around 2500-3000rpm otherwise it would stall.

Eventually it came good, unsure exactly what it was but approx 6months later the injectors died, they began stalling the car when cold, it was really difficult to start when cold and a flat spot could be felt on the tip of the accelerator, the flat spot was much worse when cold. I wasn't able to touch the accelerator if it was idling ok as it would cause it to stall instantly. Fuel consumption was bad also.

Replaced injectors, fuel consumption instantly awesome and no starting problems.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...