Jump to content
SAU Community

Recommended Posts

Any reason u went to chiptorque over say matty spryr?

What were the afr’s? Or even better, do you know what they are like when it’s coming onto boost? That way u could tell if the pump’s not good enough and is leaning it out.

Least you got it back…after today I can get stuck into my build, dan said the engine will be ready at the end of next week, if everything goes to plan, and whilst he’s got the engine, I’m getting the engine bay painted :)

Any reason u went to chiptorque over say matty spryr?

What were the afr’s? Or even better, do you know what they are like when it’s coming onto boost? That way u could tell if the pump’s not good enough and is leaning it out.

Least you got it back…after today I can get stuck into my build, dan said the engine will be ready at the end of next week, if everything goes to plan, and whilst he’s got the engine, I’m getting the engine bay painted :)

Because I was told in no uncertain terms that Mtyy Spry has gone crap...this was by someone who uses both...No I dont have the AFRs...I will have to take it back and get it looked into

Fark there is too many band wagons around this place!

At the start some one got a good tune from Matty Spry...then every one was on to him like fats kids on a birthday cake

Then I say I didnt choose him cause I heard some bad reports and now people are in a panic??

I chose Chiptorqe because people that I truseted suggested it...If Matt works for you why change that based on my personal opinion, and that didnt work out that well for me anyway!

And John why the hell do you need another tune...your car has been tuned more times than any car in the history of man kind

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...