Jump to content
SAU Community

Recommended Posts

First u go saying gtr's are Lag King's, and now ur callin mine like a diesel :happy:

P.S who said rb30's cant rev either? mine's safe for 7500rpm, and nothing extravagent has been done to allow that

Yeah Rb's tend to like RPM

First u go saying gtr's are Lag King's, and now ur callin mine like a diesel :happy:

P.S who said rb30's cant rev either? mine's safe for 7500rpm, and nothing extravagent has been done to allow that

RB26s are laggy

RB30 with you turbos is all bottom end

7500 for a built engine is low revs

yeah thats exactly what i did

well almost - more like unit and then gtst

lol

Yeah decided its time for a place, so it wont get too out of hand till i get the house.

Just be the basic, brakes, suspension, upgrade turbo, injectors and fuel pump and power fc, house then party time!!!

slo-89 - whats done to your car atm?

Bunta - same question?

Nothing its a poxy R31. But i am looking at buying Bunta's R33 in the near future, after that just a few mods till i get my house. Been around drag racing along time and am good mates with Ben Bray, so i know performance engines reasonably well.

RB26s are laggy

RB30 with you turbos is all bottom end

7500 for a built engine is low revs

ok ok with the turbos on it now yes it will be kinda like a diesel, but wouldnt u rather that than just 2000rpm of max power?

longer stroke of the rb30 means u cant rev as hard as a 'normal' 26/25, but then more revs means more wear on the engine

Yeah decided its time for a place, so it wont get too out of hand till i get the house.

Just be the basic, brakes, suspension, upgrade turbo, injectors and fuel pump and power fc, house then party time!!!

softcork :happy:

Nothing its a poxy R31. But i am looking at buying Bunta's R33 in the near future, after that just a few mods till i get my house. Been around drag racing along time and am good mates with Ben Bray, so i know performance engines reasonably well.

fare enough...

Edited by 33NIZ
slo-89 - whats done to your car atm?

Bunta - same question?

RB25 with

Wiseco forged pistons 20 oversize

Eagle I beam rods with arp2000 bolts

ARP head studs, ARP main bolts

Commetic metal head gasket

King Race main and big end bearings

N1 oil pump, N1 Water Pump

Nismo Thermostat, NGK tensioner and idler bearings

machined balanced cryo treated crank

fully serviced head with replaced valves, lifters all machined

R33 Differential

Apexi AX53B70 P25 Turbo

600cc injectors

Z32AFM

HKS Hyper 3.5" exhaust with UAS custom front pipes

Splitfire CoilPacks

OS Giken TS2BD clutch

Short Shifter

GRB Stealth FX Blow off valve

R32 GTR Fuel pump

Apexi Pod Filter

Apexi PowerFC

Greddy Profec B spec 2 Boost controller

Custom FMIC

Custom intake piping

Suspension and Braking

HKS Hyper 2 coilover suspension

Front and rear strut bars

After market sway bars

JIC adjustable castor rods

JIC adjustable upper arms

Whiteline Pineapples

DBA 4000 brake rotors

Front: 17 X 8 wheels with 235/40 semislicks

Rear: 17 X 9 wheels with 255/40 semislicks

Exterior and interior

Full respray- Custom Blue

Genuine GTR Bonnet and Grill, Front bar, and rear spoiler

GTST Type M side skirts

GTST Type M rear pods

Genuine R32 GTR Front and Rear seats

Genuine R32 GTR Door trims

Genuine R32 GTR Headlights

That pretty much covers it! Thank god for having the Autosalon list handy lol

ok ok with the turbos on it now yes it will be kinda like a diesel, but wouldnt u rather that than just 2000rpm of max power?

longer stroke of the rb30 means u cant rev as hard as a 'normal' 26/25, but then more revs means more wear on the engine

softcork :happy:

Sif use less than 9000 rpm

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...