Jump to content
SAU Community

Recommended Posts

It doesnt bother me?

are u sure its best to leave sendng it off to him, i mean, look w

what happened to the one he planned for this year.?

no offence to him meant there, just a point of view

i'll be pushing for it to be done as much as possible.

i've got 100% control over the photography so i'll be pushin ppl to the deadline to meet for the photo shoots.

as its one of the rules that its members only to the photographed for the calendar,

someone doesnt show, i'll just call anyone i know with a skyline and say "hey, get ur ass out here for a photoshoot, ur in the calendar cuz some dweeb didnt show up for his chance to be in it, so ur in".

feel sorry for me if the insurance f**ks me over, otherwise, i'll be fine :) if it all goes through fine then i get the mx5 :laugh: then i'll start showing up all the skylines, wont that be fun now!

Junior, curious about some words he saw on the bathroom wall asked, "Mom, what's a pussy?"

Mom remained calm, showed him a picture of a cat and said, "That's a pussy, son. A pussy is a kitty cat."

"What's a bitch, then?" inquired the precocious little tyke.

Mom got the dictionary out and said, "See, the dictionary says a bitch is a female dog."

Not satisfied, he asked his father what a pussy was. Pops dutifully trotted out a girlie mag from his sock drawer, drew a circle around the genital region and said, "That's a pussy right there, son. And a fine specimen it is, too."

"Well, what's a bitch, then?" asked Junior.

"That's everything outside the circle."

feel sorry for me if the insurance f**ks me over, otherwise, i'll be fine :) if it all goes through fine then i get the mx5 :laugh: then i'll start showing up all the skylines, wont that be fun now!

MX5, r u serious?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...