Jump to content
SAU Community

Recommended Posts

got it.

dont receive emails from bnecor site

only it and bnecre site ;)

lol werd

feb 2008 dude

not this year

lol

durrr i said that b4 :pirate:

aight my boss just left so i am outta here's!!

Have a good one kiddo's :kiss:

cya lil anna :woot:

Afternoon whorettes

howdy there kazza

lol werd

durrr i said that b4 :pirate:

lol

im thinkin "holly f**k, how do we have only 1 wk to get the new links installed, all the ports and wiring done?" when that all takes 4-5wks to do.

btw, u guys r hiring out 7 levels in the building

if thats anythin to go buy, we may probably end up movin this project into your building as well.

lol

im thinkin "holly f**k, how do we have only 1 wk to get the new links installed, all the ports and wiring done?" when that all takes 4-5wks to do.

btw, u guys r hiring out 7 levels in the building

if thats anythin to go buy, we may probably end up movin this project into your building as well.

yep the plans to move everyone around brisbane into the new building, some 300odd people lol

its right on the river too :pirate:

yep the plans to move everyone around brisbane into the new building, some 300odd people lol

its right on the river too :pirate:

cant move the SWRP into the building based on the lease they have already in place out at bundamba & up the road from me.

oaky & toowomba sites will remain as they are as well.

but i think it`ll be ur site, corronation drive & my site that will be moved into that office.

i`ll talk more with the management of my project next wk when they return from holidays.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...