Jump to content
SAU Community

Recommended Posts

Shane what?

That doesnt make sense, it cant be. The oil is coming from the OUTER gallery on the block then going to the INNER gallery on the filter, that cant be right. The reason I did this is because it was the only way I could get it to go to the filter before it went to the cooler!

I would of thought that they would be mirrors of each other, the relocator and the filter plate.

Shane what?

That doesnt make sense, it cant be. The oil is coming from the OUTER gallery on the block then going to the INNER gallery on the filter, that cant be right. The reason I did this is because it was the only way I could get it to go to the filter before it went to the cooler!

I would of thought that they would be mirrors of each other, the relocator and the filter plate.

dude what shit are you smoking? lol

this is how the lines should be and how it'll flow:

oil out of block into middle of oil filter

from filter to the cooler

from cooler back into block

theres only 1 way the oil comes out of the block

they just do, please post a before and after screamer pipe dyno graph i want to see if there is any at all performance from them

i cant, caus i'm not getting 2 separate exhaust made up just for back to back comparisons...unless you want to come up with 2k?

i cant use off the shelf items either, due to the extra deck height of the rb30, so from the "cat" forward it needs to be custom made >_<

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...