Jump to content
SAU Community

Recommended Posts

ahaha josh i LOL when i read the blow it out lol

put a set of forgies in a ca18 and it will be a lot tougher then an sr with forgies and nothing else

lol why cause its a cast iron block.. lol i think not anyway.. CAs are shit lol.. i hate them.. i put RBs into ca equiped cars and send them on ther way...

minus the headgasket issue's ca's are prone for :(

yep they sure r.. that crank angle sensors and case seals.

and premature build requirements on a ca, had endless ca's with headgasket issue, could be due to the fact that most are 15yrs old n well an engine that old isnt going to have the best gasket material quality :(

Re: people who budget build.

Why use cheap shit. Do it right and use something decent.

and premature build requirements on a ca, had endless ca's with headgasket issue, could be due to the fact that most are 15yrs old n well an engine that old isnt going to have the best gasket material quality :(

lol reminds me of a post i read on the forced induction section bout a fella with a RB25DE that had a WEETBIX LID for a head gasket.. or somehting like that.

Re: people who budget build.

Why use cheap shit. Do it right and use something decent.

as if.. use supertool shit and wait supa tool i think its called. and shit that cost less than genuine.

haha just get ur standard pistons throw them in ur fireplace overnight with a log roaring she'll be forged in the morning.

your keen. they got it at drive ins this weekend. tandem showing, simpsons movie and knocked up....would be good viewing

knocked up was pretty shit i thought

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...