Jump to content
SAU Community

Recommended Posts

So whos been stiring sh1t in here today...???

I missed all the action and just got a phone call about it, plus 9 reports in my inbox...???

Cheers Marc for being ontop of it, i was in a meeting...

bahaha who was reported? and who called?

sounds like someone/s really got cut up about it, christ some people need to sit back and chill out

u gonna have it ready for the photo's?

:)

the sideskirts wont be on cause they dont fit.

PISSED OFF ABOUT THAT! :O

But front bar and new review mirrors are being done today and tomorrow

other then that, the car will be ready for what can be done to it now.

PSI Parts have shit me right off this time and i am not happy.

nice, mel on here has a silver one as well. What sort of transmission? and are they aftermarket rims on it?

it's an auto... yeah yeah yeah i know i know!

:)

yeah the rims they had on it sucked wang, so i got them to put those ones on till i find ones i really like... they're 180 type x rims... they're just till i get new ones anyways...they're not big enough LOL

tell me bout it :)

:O

I hardly saw any 34's around now BAM everwhere I look!

Lucky I think they're the sex... or i'd be cross :bunny:

32's are better, but i also like 33's, and 34's arent bad, dammit i want one of each!

each to their own i suppose

hey nothing wrong with an auto (my 200 is an auto). I understand about the rims it is so hard to find a nice set that really does the car justice, but press on cause when you find the right ones the car looks even sexier

shane u dodgy little boy

stop reporting urself :laugh:

sif id do that :)

it's an auto... yeah yeah yeah i know i know!

:laugh:

yeah the rims they had on it sucked wang, so i got them to put those ones on till i find ones i really like... they're 180 type x rims... they're just till i get new ones anyways...they're not big enough LOL

LOL

thatisall :O

I speak the truth...I cannot edit posts in whoretown :laugh:

*innocent*

ur THE worst lier out, bish :bunny:

32's are better, but i also like 33's, and 34's arent bad, dammit i want one of each!

each to their own i suppose

yeah damn straight i spose it depends what the owner does with it, cos i've seen some hot 33's, but some of them make me wanna cry they are so effin ugleh!

why do people ruin such nice looking cars?

I would mind one of each :)

yeah damn straight i spose it depends what the owner does with it, cos i've seen some hot 33's, but some of them make me wanna cry they are so effin ugleh!

why do people ruin such nice looking cars?

I would mind one of each :O

find a new guy over the next 2wks..

one with a r32 and one with an r33

then marry them both without them finding out

you`ll be set

:)

yeah damn straight i spose it depends what the owner does with it, cos i've seen some hot 33's, but some of them make me wanna cry they are so effin ugleh!

why do people ruin such nice looking cars?

I would mind one of each :)

know what ya mean

this is my dream:

track built 32 gtr (getting there, shuddup everyone lol) 33 gts-t in black with gtr kit and gold rims (just like my old car *cries*) and 34 gtr

yesss that'd do nicely :O

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...