Jump to content
SAU Community

Recommended Posts

Hey guys,

Kind of silly n00b question, but im stuck, where do i begin modding my car,

Essentially i want the car to slide well (drift), but do i start with power or handeling?

The car is completely stock bar the front strut bar and a pod, should i go for exhaust or coilovers?

Any suggestions?

Cheers

(sorry for the n00b question........)

Link to comment
https://www.sau.com.au/forums/topic/120054-4-door-r32-gts-t-mods/
Share on other sites

Good to hear. I have a 4 door gtst 32.

If you want to drift a good choice is the suspention. Coilovers all around.

front mont cooler and then you can up your boost a bit.

17" wheels are better than the standard for drift, they also look far better.

you also will need to lock/remove your HICAS (rear steering) because drifting will become hard with any speed.

Mal

Edited by wal

(sorry for the misplacement of topic.... may bad)

Thanks for the info, i was leaning toward suspension, i was planning on teins and a hicas lock kit, looks like that will be my next mod!

I guess in the early learning stages power isnt important its more about technique and set up.

Thanks man.

:(

Yeah mate if you're heading for drift a set of coilovers with 8kg front, 6kg rear spring rates. Pretty good balance for a daily driver.

Make sure to get a Hicas lock BAR. As some kits only add washers to the hicas mechanism.

If you can handle a bare boot> Strip it bare.. There's a good 20-30 kgs kg's in there.

After the suspension is sorted you should really look at a good mechanical LSD. But if the stocker is in reasonable nick you could probably get away with it for a few months(cause I know stock exhausts suck). If you're really cheap you can get it 'Shimmed up'. But they rarely last more than a year after that.

That was another question i was going to ask was spring rates, thanks Drift limo!

Shimming up the diff sounds like it will cost more in the long run, what are your guys opinions on KAAZ diffs???

The lock bar is def going in, hicas is annoying :D

Should i be installing sway bars with the coils and camber arms?

Cheers guys

I have a R32 sedan which I use to compete with in Perth. The basic mods I started off with was a catback exhaust, pod filter, hicas lock, front and rear strut braces and a set of coilovers. Which I found was more than enough to start drifting on. Since then I have added pineapples, GTR skyline rear swaybar (enables slightly more oversteer), a cheap spring type boost controller and a FMIC. If I had my time again I would spend the money on buying a decent FMIC kit, preferably one which has 'switchback' piping (comes in at the right and goes back the same way) because it will for one allow you to put in a decent size oil cooler in a convinent location and also avoid the heatsoak that the piping recieves through the crossover piping (which pretty much render's the FMIC pointless).

There is no need for 17" rims or tyres. I drift on stock GTS-T rims 205/55R16's front and rear with the rears sets set to 45 psi. However if you already have them good grip front tyres are definately a necessity. Before you go drifting on the track remove your rear seat and spare tyre and then you should be able to fit 4 rims with tyres in the area where the back seat was with ease.

Having more power always helps.. but its pretty pointless if you can't use it effectively due to lack of driver skill or suspension setup. Stock power with a catback exhaust and a pod is more than enough to start off with. Allows you to drift with your foot flat as well most of the time which makes it easier to drift on.

So in your position I would say lock the HICAS as a first priority then find some coilovers and then an exhaust. And this should be more than enough to get you started.

Oh yeah make sure your handbrake is adjusted properly as well.

Cheers,

Baz, this will sound wierd but ive sen you slide at wanneroo and your the reason i got a four door.

What youve just said makes mucha sense, looks like ill be doing that switchback idea too!

Thanks for the input guys, it will be put to good use!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
    • Cats are called Bella, and Donna...  Like that poisonous plant And I remember your 2 monsters, I remember making a little bit of wee when you let them out... LOL I have already installed cat doors into the laundry where their kitty litter is, and the sun room, apart from the cat doors there's not going to be any permanent mounted stuff on the interior walls (interior doors are cheap and easy to replace) I will get a outdoor cat cage thingie once I finish the landscaping out back... https://catnip.com.au/ The only off limit areas are the main bedroom and the gym room....but, currently the cats are curled up in bed, in the main bedroom with the Mrs.....LOL, the off limits for the kittens to the main bedroom lasted about 5 minutes with Jackie I currently only have 1 free standing huge cat tree multiple level scratching post thingie in the lounge room, but, I will be getting another one soon now that I'm happy with the furniture layout in the back room and have a perfect spot for it  
    • All of this is making it seem clear that running the Coppermix twin was definitely the way to go, especially in hindsight with how insane tariffs have gotten and the strength of the USD vs yen at the time.
    • That sounds like no chance of even importing one for road registering then Now I see why Duncan wants to check LHD rules for Targa...   I wonder how "bolt in" the AWD would be if you got one imported from the US and swapped it to an AUD one
    • Not to mention they drive like a bucket of bolts! yuck!
×
×
  • Create New...