Jump to content
SAU Community

New Member

habib63
 Share

Recommended Posts

Sinista32 Grand Master

Sinista32

Posted
Posted (edited)

Hey Gaz, welcome to the SAU forums mate. Nice example of the 33.

A few of the guys will fill you in on the go. Jerra pub, Friday night cruises etc..

If your on the south side an extra Welcome.

Edited by Sinista32
Link to comment
https://www.sau.com.au/forums/topic/120327-new-member/#findComment-2216724
Share on other sites
habib63 Enthusiast

habib63

Posted
  • Author
Posted

Thanks guys for making me welcome. I have been looking through all the tuts on maintance etc but being new, I am lost in all the acronyms. Can anyone fill me in on what they are, I know ECU and AFM but there are others that have me scratching my head.

Link to comment
https://www.sau.com.au/forums/topic/120327-new-member/#findComment-2218825
Share on other sites
Amaru Veteran

Amaru

Posted
Posted (edited)
Thanks guys for making me welcome. I have been looking through all the tuts on maintance etc but being new, I am lost in all the acronyms. Can anyone fill me in on what they are, I know ECU and AFM but there are others that have me scratching my head.

If you have any questions just post them up here, im sure everyone is willing to help out :D

Edited by Amaru
Link to comment
https://www.sau.com.au/forums/topic/120327-new-member/#findComment-2219234
Share on other sites
habib63 Enthusiast

habib63

Posted
  • Author
Posted

Thanks guys for making me feel welcome. In relation to the acronyms I was talking about, another forum I used to be part of had a "sticky" where most, if not all, acronyms were posted for nubies. I found this to be a extremely helpful when you get the "I dont know to call it but....." thread. It would be a great benefit to myself and others who have become new members.

Link to comment
https://www.sau.com.au/forums/topic/120327-new-member/#findComment-2223952
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...