Jump to content
SAU Community

Rb20det Parts + Much More!


Recommended Posts

Hi Guys have the following parts from My r32 GTS4 rb20det for sale :D, as well as many new parts. Your welcome to come have a look before purchasing, i am located in adelaide, if interstate i can get you a freighting quote. Any Further Questions just ask!

rb20det inlet plenum (polished), injectors, fuel rail, fuel reg, cold start actuator,tb, tps, $200

rb20det stock dump pipe $20

rb20det stock front pipe $30

rb20det AC compressor $50

rb20det AC bracket and belt tensioner $30

rb20det rubber intake pipe $20

rb20det turbo heat shield $10

rb20det timing belt brand new $30

rb30 head gasket MONOTORQUE brand new $30

rb30 Sump Gasket brand new $20

rb20det power steering belt brand new DAYCO 4pk0940 $20

rb20det spoiler with brake light, marone in colour $120

HKS turbo elbow pipe with silicon rubber $100

R32 Intercooler Very good condition $100

Cheers FOOLBOOST

PICS UP SOONISH :)

MORE PARTS ADDED!

post-26467-1149208867.jpg

post-26467-1149208889.jpg

post-26467-1149208903.jpg

post-26467-1149208922.jpg

post-26467-1149208941.jpg

post-26467-1149208959.jpg

post-26467-1149209261.jpg

post-26467-1149209275.jpg

Edited by AM-PERFORMANCE
Link to comment
Share on other sites

I'll take the head-manifold intake gasket?

I'm also interested in the intake manifold if you will seperate the upper polished part from the intake runners, IAC fuel rail and injectors etc. I only need the lower part to make a plenum from.

Cheers,

Ian

Ian im not sure what you mean do you mean just the gaskets or the head, and manifold intake gasket, one of the gaskets goes in between the plenum and runners where as the other attaches the runners to the head, posted some pics of the head and plenum top half.

Link to comment
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Took a little trip  went to nismo hoping the get my fuel tank hoses and unfortunately they told me they didn’t have stock luckily I was able to go to a Nissan parts store and they were able to order them in for me  then can home and cleaned the tank with some degreaser and fitted the new hoses before putting it back in the car 
    • 100% I’ll hack into the 33. Strap a turbo onto the RB25DE and/or put the 25 head on a 30 block. 33 passed in cos the reserve was too high. I’ll try lowballing it again and negotiate. Aim is to have it landed and on the road for under 15k, then spend the same amount on top in mods.
    • It's generally best practise to run 1x run without VCT enabled, then 1x run enabled till redline. Overlay the two torque graphs and you'll find the desired RPM to turn off VCT. Sometimes, it might be even worthwhile turning off VCT earlier control torque/cylinder pressure and using VCT purely to spool the turbo.
    • They sell them in Malaysia for about $4
    • First time I ever have issues with Amazon, but my wife often tells me to keep an eye out for fakes. It finally got me. I wrapped up the conversation with Gates. The gentlemen I was talking to seemed to hate his job but the response time on their technical support is outstanding. He stated that the hose is marked with some variation of "SAE J30R10" but that if you only purchase a 1 foot length like I did, it is possible to get a cut between markings and have a blank hose. To no ones surprise, he stated the swelling and "gummyness" isn't normal and to replace/buy from somewhere else (He mentioned NAPA). I'll toss a small end of the new one in gas for a few days before pulling the hanger out again, just to be safe.  Hose should arrive Monday. For those running multiple pump in tank hangers, you know the joys of getting them out and back in. I'm surprised I haven't destroyed my level float yet.  Lastly once I wrap all of this up, I'm planning on hitting the dyno again in 2 weeks while I'm on vacation. I realized recently that my VCT is set to turn off at 5000RPM. I'm surprised it wasn't increased while I was on the dyno last. I'm expecting I can increase it to ~6500RPM, if not more. Should hopefully get another 15-20kw out of it. I also want him to revisit my knock thresholds. I'm occasionally getting false knock around 3000rpm. 
×
×
  • Create New...