Jump to content
SAU Community

Plz Help. Removing Turbo Timer For Inspection (pics)

Howie

By Howie,
in Engines & Forced Induction

 Share

Recommended Posts

Howie Grand Master

Howie

Posted
Posted

Hi Guys,

In order to reregister my car in SA i have to remove the turbo timer in it's entirety.

So can you tell me if i'm on the right track. It's not my car yet, so I don't want to do something that would cause the car not to start anymore.

Do I just disconnect the looms indicated in orange below?

How about the vacuum tube indicated in red? Does it need to be plugged up after it's been disconnected?

removing_tt.jpg

Thanks, for all your help!

Cheers

Quinny Rising Star

Quinny

Posted
Posted

What is their problem with turbo timers? You need to let a turbo car cool down for a couple of minutes, what difference does it make if the key is in the ignition when it is running or not?

I would like to see them get my turbo timer out. Mine is incorporated as part of the alarm system.

Howie Grand Master

Howie

Posted
  • Author
Posted

I know it's pretty silly ain't it, but I guess they have their reasons.

The RTA inspector told me, NO BOV's that vent to atmo, NO boost controllers, NO turbo timers. They're really cracking down on that right now in SA.

So can anyone tell me if what I suggested above would work?

mad082 Grand Master

mad082

Posted
Posted

it is illegal to be more than 2 meters from any car when it is parked if the engine is still running. so even if you drive an old shitter and forget yur wallet and park on the street while you run inside to get it, if the car is running you can get booked. kind of makes sense though. if the car is running and it somehow got knocked into gear it could end up parked in someones lounge room.

yeah just unplug the looms and tape them up somewhere out of the way with black electrical tape. and you will have to block the vacuum hose. just kink it then zip-tie it to itself to keep it kinked and again, tape it somewhere where it is very hard to see.

Tangles Grand Master

Tangles

Posted
Posted (edited)
If you can just hide it up under the steering bit, under the dash. Make sure its turned off tho haha, dont wanna turn the car off while at the inspection and have it stay on for 2 mins :P

Thats where mine was (and still is). I did exactly that - turned it off and it wasnt a problem. Its still off now, I think they are dangerous. But I dont mind it being wired up still......

If you are bringing a car into SA that has previously been registered interstate (like I did) you dont need to go to Regency, can go to Sturt Rd station on Tuesdays or Thursdays 9am-3pm, they check for engine / vin numbers etc. and all other bits in the engine bay.

Edited by Tangles
Fry_33 Proficient

Fry_33

Posted
Posted

Do as mad says. If the car doesn't start without the turbo timer though you'll have to find out which wires coming out of the turbo timer provide power to let you car start. Then you'll have connect that wire to an ignition wire going to the turbo timer.. or something like that. I would say that its part of the bigger plug, the smaller plug looks like it is for the handbrake cut out..

Good luck with it

mad082 Grand Master

mad082

Posted
Posted

i had mine disconnected and the car started so should be all good, but might be wired differently to mine. i actually have mine down in behind the kick panel on the trans tunnel cause the doubl sided tape holding in place keeps coming off so i just stuffed it in there till i get time to relocate it. just hope it doesn't cook it, but i don't drive it much and usually not for that long.

Howie Grand Master

Howie

Posted
  • Author
Posted (edited)

Thanks for all the input guys... much appreciated.

Tangles, I was asked if i lived 40km's from the CBD by TransportSA, that being the case i've been told that I have to goto regency rather than a police station. Think i also read that on the TSA website.

Mad082, yeah looking at the diagram you would think that's the case right? The TT just sends a kill signal back and it switches off?

Or if fry is correct, then one of the line's is working as a switch? which case I should just bridge it again once the TT is removed?

wiring_tt.jpg

edit: added image.

Edited by Howie
Howie Grand Master

Howie

Posted
  • Author
Posted
i know its a blitz. i think it is the DTT-X will sus it out for sure. i'd just try unplugging it and see what it does. leave the vacuum hooked up for now tho.

What's the diff between a DTT-X and a DTT? I know the FATT doesn't display boost and therefore doesn't have the vacuum.

I'll give it a go when the car arrives in ADL.

Btw, I've read somewhere that the battery should be disconnected when installing. I'm guessing that's not necessary here because there's not any splicing going on right? Or is it always better to be safe than sorry?

R32_Matt Rising Star

R32_Matt

Posted
Posted
QUOTE

Ahhhhh. Ain't it grand to live in QLD

yes, yes it is, but atmo BOV's are still illegal up here.

Haha. In the ACT ive had three cars inspected, all with atmo BOV's, intercoolers, exhausts etc

and all have passed first go.

It has been a while since the last time https://www.catalogueau.com/big-w/ was available.

Fry_33 Proficient

Fry_33

Posted
Posted

I just found this webpage.

http://www.240sx.org/links/installs/blitz/tt/index.htm

Assuming you have this same one then it looks like the whole turbo timer just taps into everything, ie no cutting and re-routing. Therefore you should be able to just unplug it and crimp and cable tie the vacc hose.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...