Jump to content
SAU Community

Recommended Posts

Can anyone tell me the function of the extra-rich cold start?

i mean, my car idles crap and drives jerky (liek most r32's) when its cold, but is much better when its warm..

so i have been thinking...

what if i wire up the coolant temp circuit so that it always thinks its 'hot' and always gives me a nice idle?

is this bad for the engine in any way?

this is what i got from the rb20 workshop manual:

Cooltan temp sensor controls

- timing

- idle

At cold temperatures (20deg), the sensor gives the followign readings

- approx 3 volts

- 2.5 k ohms

At warm temperatures (80deg), the sensor gives

- approx 1 volt

- 0.3 k ohms

So... if i get a resistor that is 0.3 k ohms, cut the temp sensor off, and wire this resistor into the circuit so that it always reads 0.3 k ohms, will this make the car think its always warm? or does it use the voltage more than resistance?

cheers,

Warren

Edited by WazR32GTSt
Link to comment
https://www.sau.com.au/forums/topic/120724-cold-start-can-it-be-removed/
Share on other sites

yeah but the engine will warm up with cold start maps or normal maps

what does the cold start do that the normal map doesn't? richer?

so in actual fact it makes the car warm up even slower?

what else does it to?

just saying "don't do it because it has to be there for a reason" is not good enough for me

emmission control is there for a reason, but it is usually removed on cars when modified

the stock ecu is always tuned for emmisson control remember

I think the only down side is you will running rich all the time,

even when you car is warm up!

you will get really bad fuel comsumption!

because it doesnt know what temperature is your car at, and it keep send the same pulse, and that is how much fuel you going to get all the time!!!

Your car won't start on if you don't give it the cold start "rich" map. When the block is cold the fuel wants to turn to liquid (from a gaseous spray) on the cold metal eg. the bore. Therefore you need much more fuel present to make up for the fuel that is sitting as a liquid on the side of the bore and on the top of the pistons.

Also when the engine is cold you will notice the engine idles higher, this is to help get the oil circulating as quickly as possible and to help heat everything up.

A rich mixture does not stop the engine heating up as much as you would think. Remember the engine is only near on idling.

So basically forget about it. The car won't start easily at all and the engine once it does start will want to stall as well as it not being looked after while it is cold which is when you do most of the damage.

If you have a rough idle when its cold I would be looking at other things. I have seen r32's idle nicely cold so I would be looking at leads, spark plugs and coilpacks.

Hope that helps.

Edited by nfi
Your car won't start on if you don't give it the cold start "rich" map. When the block is cold the fuel wants to turn to liquid (from a gaseous spray) on the cold metal eg. the bore. Therefore you need much more fuel present to make up for the fuel that is sitting as a liquid on the side of the bore and on the top of the pistons.

Also when the engine is cold you will notice the engine idles higher, this is to help get the oil circulating as quickly as possible and to help heat everything up.

A rich mixture does not stop the engine heating up as much as you would think. Remember the engine is only near on idling.

So basically forget about it. The car won't start easily at all and the engine once it does start will want to stall as well as it not being looked after while it is cold which is when you do most of the damage.

If you have a rough idle when its cold I would be looking at other things. I have seen r32's idle nicely cold so I would be looking at leads, spark plugs and coilpacks.

Hope that helps.

i have tried changing many things from coils to plugs to filters etc

also... R32's dont have leads

I think the fuel maps are controlled by water temperature, not ambient air temperature...

I had a very rough idle after a PFC tune that leaned eveything out. By increasing the correction (adding more fuel) at low coolant temps I have smoothed the idle out.

Be careful - you may already be too lean at cold start. Could be fuel pump, clogged injectors etc.

If you get a PFC you can fiddle with things to see what works..but the standard maps should be fine - you either have a sensor or part that isn't doing its job..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Agreed, I've never seen a 260RS specific manual. As GTSBoy said it will mostly be stagea other than the engine loom https://www.hgeconsulting.com.au/stageaservicemanual.pdf
    • You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
×
×
  • Create New...