Jump to content
SAU Community

Recommended Posts

i was going to make the same topic about a racing chip 4 my r33

my mates have been telling me to install a chip

but i have no idea who does it wat brand i should use and how much it would cost so if anyone could help in this thread it would be great

you are better off getting a chip burnt or safc tuned for your specific car than installing a one size fits all chip. alot of the chips out of japan are not good for australian fuels because they are tuned for 101 octane fuel. the jap ones run too much ignition timing and are often dangerous.

Given that its NA and you're probably not running a stripped down engine, I'd look at a piggyback. At a bolt-on level of tune the gains from going to a standalone ECU aren't worth the cost.

A'PEXi SAFC, Unichip (if they make one for your RB25DE), or the GReddy eManage / HKS F-Con etc would be fine. You'd then need to get it tuned.

But, as everyone else has said, don't get a "one size fits all" ECU. Its not tuned for your mods, so you'll either not get all the gains you could (which makes it a waste of time and money) or at worst it'll damage something.

If your car doesn't have any other mods, you'd be better off getting a catback exhaust before touching the ECU.

itll do bugger all. if you could magically reprogram the ecu and suddenly your car noticably better for racing then that would be so lovely, but if you could make the car that much better with the ecu alone, nissan would have made it like that. itll hardly make your car faster, it probably wont change you laptimes around a track etc. if you don't know that much about cars you probably wouldnt even notice a difference. to get more power out of an na 33 takes money, and you WONT get easy gains like a turbo car. you could put a full exhaust system on and make less power. you might make more. it might stay the same. Turbo it or spend $$$$$ making the RB25DE go harder (still not as hard as a turbo) OR....spend your money on things that will noticably make your car better for "racing", depending on your idea of the term..... (not the red light variety). My meaning would involve actually driving round corners.

For an NA 33, in order of how much it will improve your speed.

1. Driver training - skidpans/trackdays/motorkhanas/anything that involvers performance driving with tuition/supervision. That, and developing your understanding of the mechanics/dynamics of a car.

2. Suspension

3. Brakes

Helpful note: People that say "you should put a racing chip in it" have no idea, or are making fun of you. And if you are talking to someone who knows cars and you say that your 33 GTS has a racing chip you're going to look like an idiot.

on my NA 300zx i gained 22rwkw just from SAFC tune. no ignition timing increase. the reason nissan could not make their cars with the "ideal tuning" is because they have to run everything very safely because alot of people don't look after their cars. look at how rich factory ECU's run. NA 300zx's ideal A/F ratio is around 12.8:1, i imagine this would be not too dissimilar to NA skylines. my car before tuning was running at 10.5:1. it will make your car go faster, it will change your lap times, you will notice the difference, and you will save noticeably on fuel. it will make the car nicer to drive daily with more low-mid range torque. yes brakes and suspension are important, but i doubt that he is talking about racing his car on the track, more likely he is just using the term "racing chip" as a descriptor for modifying the ECU settings.

itll do bugger all. if you could magically reprogram the ecu and suddenly your car noticably better for racing then that would be so lovely, but if you could make the car that much better with the ecu alone, nissan would have made it like that. itll hardly make your car faster, it probably wont change you laptimes around a track etc. if you don't know that much about cars you probably wouldnt even notice a difference. to get more power out of an na 33 takes money, and you WONT get easy gains like a turbo car. you could put a full exhaust system on and make less power. you might make more. it might stay the same. Turbo it or spend $$$$$ making the RB25DE go harder (still not as hard as a turbo) OR....spend your money on things that will noticably make your car better for "racing", depending on your idea of the term..... (not the red light variety). My meaning would involve actually driving round corners.

For an NA 33, in order of how much it will improve your speed.

1. Driver training - skidpans/trackdays/motorkhanas/anything that involvers performance driving with tuition/supervision. That, and developing your understanding of the mechanics/dynamics of a car.

2. Suspension

3. Brakes

Helpful note: People that say "you should put a racing chip in it" have no idea, or are making fun of you. And if you are talking to someone who knows cars and you say that your 33 GTS has a racing chip you're going to look like an idiot.

Yes you right cookie300zx, im not gonna race on the track against other Skylines because i will probably have my arse handed to me, but hey gotta start somewhere right. I was meaning having the ECU modified. What is with the different geear ratios eg 12.8:1 & 10.5:1, what does that mean in plain english?

on my NA 300zx i gained 22rwkw just from SAFC tune. no ignition timing increase. the reason nissan could not make their cars with the "ideal tuning" is because they have to run everything very safely because alot of people don't look after their cars. look at how rich factory ECU's run. NA 300zx's ideal A/F ratio is around 12.8:1, i imagine this would be not too dissimilar to NA skylines. my car before tuning was running at 10.5:1. it will make your car go faster, it will change your lap times, you will notice the difference, and you will save noticeably on fuel. it will make the car nicer to drive daily with more low-mid range torque. yes brakes and suspension are important, but i doubt that he is talking about racing his car on the track, more likely he is just using the term "racing chip" as a descriptor for modifying the ECU settings.

if u take a closer look how SAFC works, u are advancing the ignition timing when u lean it down

if u take a closer look how SAFC works, u are advancing the ignition timing when u lean it down

cuold you explain that in more detail please. my base timing is set at 15 degrees (stock for 300zx NA) so could you explain how the ignition timing is being advanced by leaning out the AF ratio?

I saw a "LAP" chip for an rb25de on just jap's used electronics section

maybe this is the kind of thing you're after?

http://www.justjap.com/parts_uelectronics.htm

those are the things i was saying you should not be buying. would be tuned for JAP fuel, and you have no idea what the AF ratios and ignition timing would be set at! could be rather dangerous, and you won't get the same gains as a chip/piggy back that has been tuned for your car

Edited by cookie300zx

Personally i think if your going to keep your NA for a while and you love your car it can be a good idea to go for an ecu tune.

If your just going to do simple mods like exhaust&intake mods I would expect that you could certainly expect more power from getting your ecu modded.Put it this way, on my rb20de with 2 1/4 inch exhaust and k&n pod i made 85kw@wheels. Then the timing was advanced just a few degrees and it consistantly jumped up to 89rwkw's. When they mod your ecu they will generally change both your fuel and ignition maps together. If your going to run 98ron fuel all of the time then they would likely advance your timing right throughout the rev range as well as lean out your afr's a bit depending what they look like. I would say you could get maybe 6 or 7rwkw's out of it if it was done well.But thats just a rough estimate. wouldnt expect to much more than that.

The place im getting my rb20 ecu tuned for my turbo setup doesn't do rb25 ecu's yet.

Ohh and my old u12 pinny ka24e made 3.8fwkw's more after just timing advance so it gives you an idea of the extent of which tuning will effect the power of your NA.

  • 4 weeks later...

I have a rb30... Im yet to work out what it has done except add about 5rwkw. Tested it on a dyno but i just cant work out what it changed! Fuel consumption has stayed roughly the same and as far as i can tell the timing hasnt changed... The car runs a little smoother and i was told it would help elliminate any dark smoke but I didnt have much in the first place. Picked it up for $40 so i thought id give it a go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...