Jump to content
SAU Community

Tyre width

Roy

By Roy,
in Engines & Forced Induction

 Share

Recommended Posts

Roy Grand Master

Roy

Posted
Posted

My car currently runs 215/45/17 on the front, and 235/45/17 on the rear. My rims are 17x7 front, and 17x8 rear.

Im of the understanding that i could fit 215s all round, but is there any tyre performance issues other then those associated with reduced surface area, that would stop you putting a 215 on an 8" rim?

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/
Share on other sites
Al Grand Master

Al

Posted
Posted

That's a first!! I never heard of anyone wanting to go smaller in the rears.

I have F:245/35/19 and R:275/30/19. Have had no problems and just some minor rubbing of the plastic gaurd insert, as i turn up drive-ways. But the car does have a set of Tein suspension, which are relatively stiff.

PS: Gaurds have NOT been lipped, as i am not prepared to respray the car when the paint cracks.

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/#findComment-219222
Share on other sites
Roy Grand Master

Roy

Posted
  • Author
Posted

Reason for wanting to go 215s all round was firstly im able to get some R compund track tyres for good $$$, but they are 215.

The guards on my R32 have been rolled and still anything wider then 235 on the rear rubs, and anything wider then 215s on front rubs.

I have had a set of work rims on the car with different offset that allowed 255 on rear and 235 on front without rubbing, but the 255s sat outside the rear guards, looked too 13B drag Corolla for my liking.

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/#findComment-220077
Share on other sites
Sydneykid Grand Master

Sydneykid

Posted
Posted

Hi Guys, tyre sizes do vary between brands, even the same brand has anomalies. We have 235/40/17 Yokohama A032R's on the front that are 239mm wide and 245/45/17 on the rear which are 243 mm wide. So 235 versus 245 should be 10 mm wider, but they are only 4 mm wider.

Oils ain't oils, Sol.

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/#findComment-221651
Share on other sites
PuppaDuck Collaborator

PuppaDuck

Posted
Posted

I have 235/40/17 on the front and 255/40/17 on the rear...

I have noticed that the front tyres wear unevenly now...

The inside 1 inch wearing bald while the majority of the tyres are chunky as...

Anyone else getting this ?

I am told that sometimes Skylines do this, or that wide tyres cause this...

Also finding that the guard-liners are wearing against the front tyres somehow...

Thing is, I've had it for years and its only started doing this in the last year...and I can't figure out if it is worn suspension or my driving on corners...

The initial indicator I noticed in the area was that the guard liners pop to the outside of the guard lip, and I have to sometimes push them back in behind them...

I'm interested to find if others have any similar signs...

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/#findComment-233736
Share on other sites
Roy Grand Master

Roy

Posted
  • Author
Posted

Last time i got a wheel alignment i started going thru front tyres...too much camber.

Didnt notice any difference either by feel, lap times, or in consistancy so have dropped some camber out of the front. Tyres seem to be wearing better now.

You R33 owners are spoilt, just like my friend in his 200SX, your guards swallow 18s, even 19s, or nice and wide 17s.

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/#findComment-235215
Share on other sites
Al Grand Master

Al

Posted
Posted
Originally posted by Roy

You R33 owners are spoilt, just like my friend in his 200SX, your guards swallow 18s, even 19s, or  nice and wide 17s.

What you mean OR, i have the best of both: 19" x 8" rims all round with F:245/35/19 and R:275/30/19. :D :shake: :) :shake:

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/#findComment-235548
Share on other sites
Sydneykid Grand Master

Sydneykid

Posted
Posted

Hi PuppaDuck, tyres wearing on inside = too much negative camber or incorrect toe settings. Puting wider (or narrower) tyres on should not affect the suspension geometry. Either way have it checked. Toe should be set at zero or slightly toe out. Camber is a little more tricky as it depends on your driving style. Anything more than 1 degree negative on a road car can be a problem.

If you like the handling feel of negative camber, try more caster instead. All of the advantages, but no increase in inside tyre wear.

Hope that helps.

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/#findComment-236470
Share on other sites
PuppaDuck Collaborator

PuppaDuck

Posted
Posted

Thanks SydneyKid...

I'll put this to the next guy I go to for a wheel alignment...

I have no personal choice nor do I know what to ask for...

But if I can get front tyres to last longer than a year by wearing even then I'll be happy...

Maybe he was put off by not knowing what settings to put it on cause the R33 isn't in his book...or perhaps he wasn't sure about the HICAS...

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/#findComment-236478
Share on other sites
Sydneykid Grand Master

Sydneykid

Posted
Posted

Hi PuppaDuck, since HICAS is rear steering I have no idea why that would effect what he thinks should go on the front. I'd find a better wheel alignment shop. We use Whiteline (Wedge) at Minto or Heasmans (Doug) at Sydenham. East Coast are also OK.

The "local tyre shop" is generally a waste of time.

Hope that helps.

Link to comment
https://www.sau.com.au/forums/topic/12182-tyre-width/#findComment-236946
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...