Jump to content
SAU Community

Recommended Posts

hey guys, ok i went away for a week and a half came home and my R33 gtst wouldnt start the car was perfect when i left. came home had no power at all, tried jumpstarting it, got power to everything but when i tried to start it, it made a ticking noise for a while then nothing, tried a couple of times and got the same result.

Next day went out same thing no power tried charging it, still nothing, then i had power to everything tried starting it got nothing all my lights work everything but wont turn over it stopped making the ticking noise but still wont turn over, i checked my battery that fine, tried tapping my starter did nothing. all fuses are good spark plugs are good.

NEED HELP ASAP, thought maybe it had something to do with my imobiliser, but doesnt seem to.

i heard u cant put a starter from an auto into a manual is this true?

what else can i try...

Link to comment
https://www.sau.com.au/forums/topic/122605-r33-wont-start/
Share on other sites

Ermm. Sounds like your battery died.

Either:

It has a tiny bit of juice to work the lights, but not enough to start. The clicking noise is usually the solanoid that pushes the starter gear onto the ring-gear (or whatever manuals have)

Or:

Did you jump it from the battery in the boot, or off the fusepanel under the bonnet like you're supposed to? If you have a good battery, but still nothing happens, you could have blown your starter motor fuse. Check that fuse.

Either way, if the battery died after a week, it's time to replace it.

Link to comment
https://www.sau.com.au/forums/topic/122605-r33-wont-start/#findComment-2264876
Share on other sites

chances are its your battery as RANDY said.

to get it started keep the car thats jumping you at around 2000rpm with all electrics off (radio, lights etc), give the battery time to build up some power then turn it over.

i bought a new (cheapo) battery after the first time i got my car on the road after the first rebuild, 2 days later i took it off the road (didnt disconnect it) and 2 months after that i tried starting it and not only was it a complete c**t to start, it wouldnt turn back on if i turned it off.

moral of the story - disconnect your battery if you're not going to drive it for a while, especially if its crappy/old.

Link to comment
https://www.sau.com.au/forums/topic/122605-r33-wont-start/#findComment-2265197
Share on other sites

i got the sameproblem mate, wqent away for the long weekend and left my f***n light in the car on, the car didnt start , even with jumper leads from a barina the car was making a ticking noise but just wasnt turning on... i had a 6 month old battery so the nrma came and jump started it with a high powered battery,

my guess is skylines need alot more power than normal to start????

Link to comment
https://www.sau.com.au/forums/topic/122605-r33-wont-start/#findComment-2265947
Share on other sites

i took the battery out and put it in another car and it worked perfectly, and had it tested so i know its deffinatly not that.

i checked the fuse's there all good.

You're talking apples and oranges. A half-dead battery that couldn't start a V10 Viper would have little trouble coughing up the CCAs to start a Toyota Echo, if you follow what I mean.

What voltage do you have on the battery? How did you have it tested? The only reason people are pushing the battery thing is because all your symptoms are the same as a dud battery.

The only other potential cause could be your immobiliser. Depending upon the model, it may be built to detect a loss of power and shut itself down (ie immobilise the car). It's a long shot though as you've already said you can hear the starter solenoid firing...

Link to comment
https://www.sau.com.au/forums/topic/122605-r33-wont-start/#findComment-2266498
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...