Jump to content
SAU Community

Recommended Posts

hey people

http://www.nomorefines.com.au/index.html

Thats the site

someone at work posted a link.

anyone bought one of these..

anyone got something decent not by this mob?

And if possible... if you can manage....try not to post the usual...if you stay in the speed limit...you wont need one... blah blah blah

Link to comment
https://www.sau.com.au/forums/topic/122940-radar-detectors/
Share on other sites

WA cops don't use handheld RADAR anymore

Hmmm..yes they do

Got done by one a few months back :P

Country cops still also use a lot of gutter mount radars, which are the easiest of the lot to detect :(

Edited by PSI_GTSII
Link to comment
https://www.sau.com.au/forums/topic/122940-radar-detectors/#findComment-2271726
Share on other sites

i was using a rx65 pro for about a year before it broke :)

i found the false alarms were anoying and also when it picked up ka band (multanova) from the other side of the road

i also found that they only really helped if doing up to 10km/h over the speed limit.

going any faster it usually picks it up too late.

btw i know the people that run this small business

luke

Link to comment
https://www.sau.com.au/forums/topic/122940-radar-detectors/#findComment-2272490
Share on other sites

Hmmm..yes they do

Got done by one a few months back :P

Country cops still also use a lot of gutter mount radars, which are the easiest of the lot to detect :D

really? my bad :D

I've never seen one being used once (I've only been driving two years though...). I can see how country cops might still have them but everytime I've seen a handheld in Perth its been a lidar.

Considering I got flashed yesterday doing the speed limit, I think there worth it. I was right next to another car so if they managed to get my plate they would have definately got my fellow law abiding motorists plate aswell in the same shot.

Alot of court cases in other parts of the world (including aus) have ruled in favor of the motorist when it comes to handheld radar. They've been proven clock trees at 70km/h in some cases...

The beam width of radar can't be focused anywhere near as much as lidar so at a distance its very unreliable. Multinovas are short range so there usually accurate... unless you next to another car :)

Whether you can justify the money is up to you.... but I'd definately look at eBay before Perth dealers

Link to comment
https://www.sau.com.au/forums/topic/122940-radar-detectors/#findComment-2272506
Share on other sites

So is it really worth gettin a Radar Detector?

No.....

The only thing that would sway me into buying a Radar detector (Again!) would be if I did a lot of country driving, as mentioned before the Country cops still use the old gutter mount style radar, and as most of them are left on most of the time they are very easy to detect.

Around town Multinovas are your main worry, and I cannot put up with all the 'falsing' that radar detectors give you around town.

From my experience (2 x Unidens & 1 x Bel) they do not detect multinovas until the multinova is triggered....if you are the car triggering the multinova basically you are screwed, hopefully it is a car up the road triggering it so as it gives you a chance to slow down.....but then as the detector has probably beeped at every Maccas and BP servo you've driven past you'll probably ignore the warning anyway... :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/122940-radar-detectors/#findComment-2272628
Share on other sites

WA cops don't use handheld RADAR anymore.

saw a cop on mounts bay road near the narrows bridge on my way to uni a few days ago too. They wait near the bend before u go under the narrows, ie coming from the bell tower -> swan brewery. They usually sit there with the gun...

few other notables but thats the only one i can think of for now. my car struggles to boost now anyway so its not like i can speed very fast anyway :thumbsup:

and my car's generally slow even when it IS healthy

Link to comment
https://www.sau.com.au/forums/topic/122940-radar-detectors/#findComment-2272640
Share on other sites

Your right about the lidar, radar detectors arent effective against them due to the fact they are only on when the officer pulls the trigger.

But your wrong about the multanova. Its not "triggered" when a car goes past it, its constantly left on and constantly emmiting a signal. It emits its signal in all directions, but its only the signal directly infront of the gun that gets reflected back to get your speed. Thats why detectors give you prior warning because it picks up the signal that has bounced and reflected down the road. Check out howstuffworks if you want to know the specifics, they have a good article on rds.

But yeah I got a X50 from this mob a little while back, and im pretty happy with it. The range it gives does vary, but I have seen it give 20+ seconds warning at its best. I can't drive without it now. I had an RX65 before till someone broke in and stole it. NEVER leave your suction cups on the windscreen!! I learnt the hard way=( But yeah it is definately noticably better than the RX65. The RX65 probly could give the same range at its best, but I found it was just less reliable. The Rx65 on the odd occasion would only alert me as Id basically pass the camera, but the X50 has never given me less than about 7 seconds at its worst. Generally its about 10-15 seconds. But even 7 seconds is enough to save you if you aren't being ridiculous. Plus they say the multis range is only 40m and 7 seconds at 70kmh is 135m.

As for false alerts, they do occour on the X and K band, but you just turn the X band off cause its not used here... but there are no false alerts on the Ka band. So if they are pissing you off then you can just turn off K and X band for city driving and leave Ka on just for multanovas. I personally just put up with a few false alerts on the K band for the chance to be saved from a cop car.. plus I just like to be reminded that its still working=)

Edited by millicent
Link to comment
https://www.sau.com.au/forums/topic/122940-radar-detectors/#findComment-2272695
Share on other sites

  • 2 weeks later...

been looking into this for a while now - lidar is pretty much impossible to avoid - because they have such a narrow beam that once your fetector picks it up (if it does at all) they've got you. lidar are generally aimed at your grille area - as they supposedly need a fairly flat surface to get a good read. dash mounted detectors - especially high mount - usualy miss them. the 'undetectable' radar detectors that they're flogging now are still dash mount - when i see a hard wired unit that has the pickup in the grille area i might reconsider but until then - i'll just keep my eyes open.

Link to comment
https://www.sau.com.au/forums/topic/122940-radar-detectors/#findComment-2296718
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...