Jump to content
SAU Community

Recommended Posts

Seeing if anyone knew if the R34 Neo 5spd manual transmission will work on the R33 RB25DET?....I have an S13 right now with an RB25 in there and had the stock R33 5spd, but it gave out and cant find that many R33 transmissions around. Found this R34 Neo transmission that I can pickup, but wanted to make sure that the bell housing would bolt up to the back of the block without a problem and also check to see if it is the same general overall size so that I wouldnt have any troubles with the tranny tunnel or driveshaft that I had made for the R33 setup.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/123533-r34-neo-transmission-on-r33-rb25/
Share on other sites

yes it will.

youl need the shifter and a pull clutch/flywheel asembly.

either.

r33gtr or r34gtt. 250mm clutch :)

i had one in my dr30. nice box with good ratios and very smoth operation.:wub:

I am about to fit an R34 box into my 33GTSt. (Auto to manual conversion)

Can I use an R33 GTR flywheel with a pull type clutch?

  • 2 months later...

so has this been done before? does it fit straight on without any mods (apart from the flywheel/ can R33 flywheel fit?) or is there more to it and if there is plz explain

Edited by assyrian4evaa
so has this been done before? does it fit straight on without any mods (apart from the flywheel/ can R33 flywheel fit?) or is there more to it and if there is plz explain

as T04GTR said, all you need is the gear lever and pull type clutch.

everything else bolts straight up.

  • 4 months later...
  • 2 weeks later...

Why do you want to put a r34 box in it?

Works out cheaper to put the 33 box in doesn't it? And push type clutches are cheaper....

I just got my car back from a manual conversion So just curious

P.S help me out here: http://www.skylinesaustralia.com/forums/in...howtopic=154422

Why do you want to put a r34 box in it?

Works out cheaper to put the 33 box in doesn't it? And push type clutches are cheaper....

I just got my car back from a manual conversion So just curious

P.S help me out here: http://www.skylinesaustralia.com/forums/in...howtopic=154422

I got an R34 box as it was all I could find at the time.

Push type is cheaper.

For your conversion you need the wiring harness from the gearbox up to the fuse/relay box on the drivers side inner guard for the reverse lights to operate.

For the speedo to work you need the manual speedo gear drive in the box and a manual speedo head or it may be easier to buy a complete cluster second hand.

Dont ask me why Nissan have a manual and auto speedo head, but they do.

Hope that helps.

Stan

Edited by Stan
Seeing if anyone knew if the R34 Neo 5spd manual transmission will work on the R33 RB25DET?....I have an S13 right now with an RB25 in there and had the stock R33 5spd, but it gave out and cant find that many R33 transmissions around. Found this R34 Neo transmission that I can pickup, but wanted to make sure that the bell housing would bolt up to the back of the block without a problem and also check to see if it is the same general overall size so that I wouldnt have any troubles with the tranny tunnel or driveshaft that I had made for the R33 setup.

Thanks

Buy the R34 box and swap the front housings over, i just finished doing this 26 conversion with R34 box in S13 ( www.uras.com.au/democar.htm ), i hate pull clutches so used a R32 GTR housing but R33 GTst works exactly the same.

Edited by URAS

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...