Jump to content
SAU Community

Recommended Posts

Hi guys,

i just fitted a new H/D clutch and changed my gearbox oil (Redline). However, i noticed that my gearbox sounds pretty loud. It's the grinding sound that i know you normally hear but i feel that mine is exceptionally loud!

The clutch sounds loud as well when i release the clutch to neutral, only when i 'clutch in' then the sound goes away.

Is anyone going through the same situation as i am or it's pretty much normal or i can do something to decrease the noise besides increasing the volume of my stereo?

Link to comment
https://www.sau.com.au/forums/topic/123617-gear-box-noises-on-skylines/
Share on other sites

was it just a heavy clutch or a twin plate. if it is a twin plate, then they always make noise. if it was just a heavy single then the noise is most likely a noisey input bearing. i have the sound noise and thats what i got it diagnosed as.

What type of noise is it.. rumbling?.. whining??..

Sounds like it's probably on the input shaft bearing if it's when clutch is out in neutral..

Mines currently got a similar issue, however 20x worse.. sounds like i've got straight cut gears..

Yes links it's the whining noise. Sometimes u can hear it when u release the throttle. How bad is yours?

Is there any way at all to fix it?

No mate you'll be allright, I have the same problem and most of the people I know it is a bit annoying but you get use to it i suppose.

It can go for years apparently until it finally dies on you, and if you are smart you would have saved some money and get an RB25 second hand gearbox put in. apparently they are tougher than RB20's.

Cheers

Sorry for the late reply..

Mine is really loud on acceleration/deceleration.. so whenever you put load on it really..

You could look at recoing the gearbox.. no point replacing an input shaft bearing and that's it as they need to remove the front bell housing off..

$400 labour to pull it down..

$300 labour to reco gearbox

+ parts..

2nd hand R33 gearbox - try $1400 in unknown state.. so see how annoying it is..

Than again.. with these things you never know what it could be.. maybe goto a gearbox specialist and get a recommendation..

With the clutch in.. e.g. foot on pedal.. and free revving it - can you hear it??..

Also - in 1st/2nd.. rolling down a hill with the clutch in.. can you hear it??..

Edited by Links
No mate you'll be allright, I have the same problem and most of the people I know it is a bit annoying but you get use to it i suppose.

It can go for years apparently until it finally dies on you, and if you are smart you would have saved some money and get an RB25 second hand gearbox put in. apparently they are tougher than RB20's.

Cheers

I don't drive an r 32, i've got a 34 :) but i don't think a 33 gear box can fit into a 34?

Links, PM sent

Well.. I would.. but my one got replaced about 300kms ago..

I've got a rattling/squeaking thrust bearing as well.. but it appears to be going away as it maybe grooves in or something.. not sure what the hell is up..

does the rattling go away when you depress the clutch pedal??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...