Jump to content
SAU Community

Recommended Posts

I’ve got some very light scratches on my bonnet due to it being washed with a scrubber which was a little too ruff. They are probably only 1/10 of a mm deep, & can only been seen in the right direction of light which causes them to reflect.

I tried wax, “wax on, wax hoff”, but did not work well enough. Is there a product which can remove these light scratches?

Thanks :P

A cut and polish should do the job. It should take about a 10th of a mm off your clear coat, which would even it down to the depth of the scratch. (and is also why you shouldn't cut and polish more than once a year apparently)

just be carefull when you do it...

1.minimal elbow grease - small amount of cut and light pressure - you would be amazed how quickly you can f*k your paint

2.do the entire panel in an even manner - other wise you will end out with a visible faded area.

luckily your car is white! white hides all :glare:

Jolinator PM's Sez:

please dont use cut an polish on your car, that shis is for commodores not proper cars, if you want to remove the scratchs properly without doing more damage to the paint, get yourself a bottle of meguairs scratch x, is has special particles in it that will smooth the scratchs over, without ripping off clearcoat etc,

i am a detailer for a living so if you have any questions let me no.

Good one :ermm:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...