Jump to content
SAU Community

Recommended Posts

i now have another problem, that i am getting very stressed about, due to there being a track day on saturday that i REALLY want to make it to....

there is a noise coming from what seems to be the front left wheel.

at first i thought it might be a stone in the tyre - nope.

what it sounds like, is a 'plasticky-sounding' clicking/whirring/grinding noise that increases/decreases with wheel revolution, only seems to start once the car has warmed up (i.e. doesn't do it first thing in the morning).

I dropped into my suspension place on the way to work this morning, and he seemed to think everything is fine, and that its just a high spot in the pad or rotor that rubs at a certain point....

now, i've heard what he's describing before, and it sounds nothing like that, and the other thing that makes me think its not that, is that the noise is still there when you're using the brakes (i.e. if you left foot brake and still drive along, its still there etc)

now, this has me stumped, and fairly worried...

HELP!!!!

Link to comment
https://www.sau.com.au/forums/topic/123748-possible-dyingdead-wheel-bearing/
Share on other sites

to check wheel bearing, jack up that side of the car, and try moving the bottom of the wheel toward you and away, to feel for play. If you get play, it's a sign the wheel bearing needs replacing.

-check that the plate behind the brake rotor isn't rubbing, this is quite common and will make a metallic scraping sound

-maybe take to a brake place and check the run-out on the rotors etc.

-check for any thing that looks like it might be rubbing on something (loose cable, loose inner guard lining etc.)

where can you get new bearings from and roughly how much? i have a noisey wheel bearing too (oddly enough its the front left too - get a few more people with them and we should hit nissan up for a product recall). i haven't even started looking yet, so i figured since there is a thread about it i might as well ask.

I`m with mad 082.My f/left and r/left are slightly worn and need doing.Saw the tutorial but looks a little dodgey.Still,if Advan can quote $560 for rear then I`ll look at options.

My left front was replaced 4.5years ago. :D

It cost me $250 inc. labour, the others have been fine since.

Mine was silent when not turning but rather loud and worrying when turning slightly, it was noticable at around 40-50km/h around a corner as you approached 80km/h it was so wirrr r r r r rr that it was worrying.

My left front was replaced 4.5years ago. :ermm:

It cost me $250 inc. labour, the others have been fine since.

Mine was silent when not turning but rather loud and worrying when turning slightly, it was noticable at around 40-50km/h around a corner as you approached 80km/h it was so wirrr r r r r rr that it was worrying.

This is pretty much what it's doing.... when the wheel is straight, it doesn't do it (well, it used to, but doesn't seem to any more) only does it when the steering wheel is slightly offcentre, and to the right

It's cheap to get rotors machined and despite what it seems like in this thread Skylines actually only fairly rarely do wheel bearings.

If you've seen a Skyline wheel bearing out of the car you'll understand why. They are bigger than any other wheel bearing I've ever seen. (Not to say bigger ones aren't out there, just that I haven't seen them.)

I suggest doing the rotors first to see if that's it then if not look at doing the wheel bearing.

If it helps, i had the same problem on my 32 (and on my 78 golf) both times it sounded like a dry bearing, or like something that is spinning and needs greasing. Was noticeable with clutch in and changed pitch at different speeds, Also was only noticeable turning right at first then eventually noticeable going straight to. $450 is insanity but i suppose everything is expensive on imports. Can you just re-grease them or are they sealed.. in which case they wouldnt need re-greasing, but re-placing anyway

Edited by r32 gts-turbo
It's cheap to get rotors machined and despite what it seems like in this thread Skylines actually only fairly rarely do wheel bearings.

If you've seen a Skyline wheel bearing out of the car you'll understand why. They are bigger than any other wheel bearing I've ever seen. (Not to say bigger ones aren't out there, just that I haven't seen them.)

I suggest doing the rotors first to see if that's it then if not look at doing the wheel bearing.

I agree they are friggin huge. realistically these cars are getting damn old. God knows how many kays some of them have 'really' done.

By the look of certian wear many 60-80,000km R32's a few years back have really done 200,000+ km's.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...