Jump to content
SAU Community

Recommended Posts

19x8 Koya Inox 1 wheels in perfect condition

front tyres are about 85% tread

rear tyres have inside camber wear can rotate around or replace with legal tyres.

wheels are in great condition,they will suit r33 gtst (not sure on other models)

will post anywhere in aus at buyers expense

im chasing $1700ono

0434589274 or [email protected]

Justin

post-29137-1151481541.jpg

post-29137-1151481585.jpg

Link to comment
https://www.sau.com.au/forums/topic/124140-for-sale-19inch-koya-inox-1-wheels/
Share on other sites

soooo y r u selling them for 1700 when they were for sale for 1500?

refer to this link

http://www.skylinesaustralia.com/forums/in...howtopic=119033

they were for sale for 1500, probably got them cheaper, so unless you have put on new tyres or somthing your asking to much

just trying to keep the forums fair man

ok well since u cant keep your nose outta other ppl's post's without knowning any of the story? reason im asking 1700ono i paid $1500 i didnt get them any cheaper then there is a pallet cost and freight ontop, have u recently priced these wheels? 400 a rim then postage on top then new tyres on top of that...but one rim was damage on the inside where he hit a pot hole i was unaware of it when i bought them,i dropped it at engineering place got it fixed and im just chasing back what i paid..so before u go ahead and make comments thinkin im trying to scheme ppl think again.

Once again im not trying to sell these wheels to make a profit,but im simply trying to sell them as i cant afford 19" wheels,i should have never gone and bought wheels to start with,im only earning $250 a week and with camber my car has tyres wont last longer then 4000kms for a set so its just reality they will send me broke..so i rather get rid of them and drive on stockos..i aint out 2 try n make money off them just get back what i have paid + fixed rim

Edited by l0WRB
  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...