Jump to content
SAU Community

wrx goes bang

Guest aw11

By Guest aw11,
in Engines & Forced Induction

 Share

Recommended Posts

  • 6 months later...
Anquetil Mentor

Anquetil

Posted
Posted

Thats gold! They dobbed him in!...

"YOU GUYS ARE ALL ****IN ASSHOLES!!!! I CAN"T BELEIVE YOUR ****! WHY THE **** WOULD YOU BE SUCH AN ASSHOLE TO REPORT THIS! YOU GUYS ARE SUPPOSE TO HELP OUT AND BE ON MY SIDE, NOT **** ME OVER! **** ALL OF YOU! **** ALL OF YOU! **** ALL OF YOU! I AM GETTIN RID OF THIS PEICE OF **** CAR, AND NEVER BUYIN A SUBARU AGAIN!"

Link to comment
https://www.sau.com.au/forums/topic/12432-wrx-goes-bang/#findComment-565639
Share on other sites
Cubes Grand Master

Cubes

Posted
Posted

I must admit I would go back to the dealership.

You would be stupid to tell any one what you were doing.

Mind you If I had the money to replace the motor I would.

Except the internals would be a lot nicer. :P

Then again I wouldn't mod the car and do some thing as stupid as he did without knowing I could replace the motor if it went bang.

The world is a cruel place. :)

Link to comment
https://www.sau.com.au/forums/topic/12432-wrx-goes-bang/#findComment-565906
Share on other sites
predator Grand Master

predator

Posted
Posted

hehe, well american - explains 95% of it.

Just lucky with the Nissans the stock turbo goes pop before the rest of the engine does :P not a bad Idiot proofing. Doesn't say much for the intelligence of the WRX management though to let it hose itself without some sort of basic protection. Then again, it does sound like he lost an oil line to the turb .. not much you can do about that i guess.

Link to comment
https://www.sau.com.au/forums/topic/12432-wrx-goes-bang/#findComment-565980
Share on other sites
wannabe Proficient

wannabe

Posted
Posted

Holy crap.

OK, the guy was a bit of a novice and overmodded his car. BUt you have got to be a sick twisted ***hole to dob someone in to the dealer over this one.

I mean like he said he did get it done by a mechanic and they coulda/shoulda told him or warned him.

Makes you appreciate good tuners!

Link to comment
https://www.sau.com.au/forums/topic/12432-wrx-goes-bang/#findComment-566794
Share on other sites
dAVE Grand Master

dAVE

Posted
Posted

I would try and defraud the dealership too but I have no morals. What they did was harsh, but on the other hand, he did deserve it.... and he was pretty foolish, especially going to a 3rd dealership and signing saying he hadnt modded the car.

Would love to know what happened to him in the end.

Link to comment
https://www.sau.com.au/forums/topic/12432-wrx-goes-bang/#findComment-567178
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 33GTRV
      Rb26 iron block limit

      By 33GTRV · Posted

      Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • GTSBoy
      RB25DET Series 1 & Series 2 Gearbox Identification

      By GTSBoy · Posted

      thumbsup
    • AdiR34
      Did tie rods. Steering now not "springing" back.

      By AdiR34 · Posted

      Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...