Jump to content
SAU Community

Recommended Posts

yeah they will be fine at that power level, i would expect somewhere near 80% duty cycle, somewhere near there. just make sure you have a good pump to keep up and it should be fine.

fuel injection is irrelevant of turbo, boost pressure etc. it purely comes down to how much is being induced and how much fuel you need to maintain the levels and make it combust

the s15 injectors must be manual JDM ones.

australian s15 injectors are only 370cc like the R33 stockers

Hi Paul. With the stock R33 injectors what would you think

they are capable of. Obviously with the supporting mods

such as fuel pressure reg, pump etc. Also im currently

using the walbro. Do you think they are that bad? Im

after around 230-240 mark. Should i change to a 040?

Thanks. :D

Edited by mickr33
the s15 injectors must be manual JDM ones.

australian s15 injectors are only 370cc like the R33 stockers

Nope. ADM is 440cc aswell. They are not 480cc as everyone says because they were measured at a different pressure.

You should get about 345 rwhp out of a walbro.

They don't pump as much as a bosch 040 or 044.

I don't think they're bad at all. I know one guy on here who had a walbro that sucked in it's filter. And I've heard a lot of people have bought dodgy chinese knockoffs sold as walbro's. The knockoffs don't pump muh at all. (Just amke sure it's real!!)

But I think they are a good replacement for the stock GTST pump - although not huge.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...