Jump to content
SAU Community

Recommended Posts

SOLD

I have a white 1994 R32 GTR that I recently just imported.

I have import approval, all customs and quarintine clearance papers and have already paid a

deposit of $1000 for SEVS compliance.

Unfortunately the oil pump shit itself and motor ran without oil for a bit so the engine needs a rebuild or the car will need a new engine before it can be complied and registered. The motor still cranks over(hasnt seized) but doesnt start. I am going to do a compression test in next few days.The true condition of the damage done or condition of the engine will only be known once its stripped down.

So if you buy this car you have to pay remaining $1700 for compliance and pay for rego.

as well as rebuild the engine.

The car is very neat and tidy and also has aftermarket suspension, heavy duty clutch,strut brace and

3.5 inch exhaust

Interior is very clean, the car has 123,000 k's.

It is a good potential buy for some one who was going to rebuild to a stronger engine anyway.

If you do the Maths you could have yourself a nice 94 R32 GTR with a fresh engine for

around 19,000 -20,000 depending on the cost of the rebuild.

At the moment I just cant afford to rebuild or buy new engine for it as I am strapped for cash and just want to get rid of it, as I also have another car getting an engine built at the moment as well

I am looking for 11,000 for it and am located in Melbourne.

post-14428-1151992858.jpg

post-14428-1151992955.jpg

post-14428-1151993235.jpg

post-14428-1151993454.jpg

post-14428-1151993590.jpg

post-14428-1151993024.jpg

Edited by >GoDziLLa<

Im very interested in your car but i need to know more. If i bought it i would have to get it freighted up, because i am in Queensland. Are you sure it is a R32? I didnt think they made them in 94'. If its a R32 is it twin turboed? So it needs a complete rebuild? email me [email protected]

Im very interested in your car but i need to know more. If i bought it i would have to get it freighted up, because i am in Queensland. Are you sure it is a R32? I didnt think they made them in 94'. If its a R32 is it twin turboed? So it needs a complete rebuild? email me [email protected]

Yes, they did manufacture R32 GTR's in 1994, and yes it is twin turbo being a GTR.

Who's compliancing it?

Also, where abouts in Melbourne are you located. Am interested in checking it out.

The people compliancing it are called Imported vehicle compliance centre in Craigieburn, they were one of the first workshops to get the SEVS plates for late model R32's

I am located in western suburbs. Taylors Lakes

The thing needs a rebuild and someone is worried about a $50 part.... it never ceases to amaze me.

Great price for a late model GTR in anyones language, rebuilds are costly but even factoring that in its a bargain! Best of luck with it!

Also spoke to the compliance place today and they said it would be fine for whoever bought it off me to takeover the compliance and pay the rest and also they said they don't mind how long it takes for the rebuild to get done and then bring the car to get complianced(even 2-3 months). Just as long as its running when you bring it to them.

and as Morgs said if you do the maths you still get a late model GTR with a fresh engine for a good price.

11,000 - to buy the car off me

1,700 - remaining compliace cost.

1,000 - registration costs

= 13,700

so even if the rebuild costs you 6 grand it would only be like 20,000 all up.

If you can get the rebuild cheaper, have another RB26 to put in or can do it your self it would be an even better bargain.

Edited by >GoDziLLa<
the rear right tailight cover is cracked. I can get one from wreckers for 70-80 bucks already in white

Aint just your light. your whole boot aint even sitting straight. any leaks in it? if not is there a chance rain could get into the boot if left out in the open?

Hi,

You might want to check the implications of selling the vehicle before a compliance plate is fitted.

Import approvals state "To sell the vehicle or use it in transport in Australia before a Used Import Plate is affixed could be an offense under section 16 of Act etc"

DoTaRS should be able to clarify this for you.

Cheers

Jo

Aint just your light. your whole boot aint even sitting straight. any leaks in it? if not is there a chance rain could get into the boot if left out in the open?

its just the light cover thats not sitting straight.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...