Jump to content
SAU Community

Sau Nsw 3rd Official Track Day For 2006

Abo Bob

By Abo Bob,
in Events Archive

 Share

Recommended Posts

ido09s Mentor

ido09s

Posted
Posted

what is the track like for pictures??? I would volunteer if i knew i would be there and be staying all day long but as its my only day off for the week i will more than likely catch up on some sleep..... if i do make it though i will certainly be snapping a few pics

  • Replies 640
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

hanyou Grand Master

hanyou

Posted
Posted

yeap ill try.. ive got a friend who is interested (well im trying to make him come lol) with evo 7 if thats ok.. however his not a member of any CAMS affiliated clubs. i assume u will still need to be part of a cams club even for the 1 day license?

Primordial Grand Master

Primordial

Posted
Posted

I'm a little curious how this 3 lap thing is going to work..

Wont we get people who are having their 'flying' lap come down the straight and end up stuck behind people who will be doing a 'warmup' lap, or are all the cars for the session released onto the track before any car has done their 1st lap?

I'm just trying to picture it in my head :P

wilch Grand Master

wilch

Posted
Posted

Hey Adam, (or anyone else that knows... need this info asap)

Do you need to be a member of a CAMs affiliated club to be a elligible for a CAMs day licence?

...and would you think a car that normally runs 2:14-15 around the track is too slow?

N1GTR Grand Master

N1GTR

Posted
Posted
Steve can't be flaggie anymore, got work..
N1GTR?
yeah him.

What. the. f**k. is. this.

Adam, id suggest you ignore TRUBLSM as he has no idea what he's talking about.

I do not have work on Sunday unless he knows something i dont.

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      No engine fan = quieter getrag ???

      By Butters · Posted

      Saw this video today from Adam LZ.    Long story short is he is claiming that the load from the engine fan once the fan clutch heats up(engaged) is increasing the getrag rattle(at idle) when you don't have a dual mass flywheel.  Before I go buying an electric fan setup .... Anyone heard of this ?    I must admit when my car is cold the getrag is pretty quiet and I do notice the rattle after it is all warmed up. I've always assumed this is due to the gearbox oil temp and tolerances of metal.       
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Yep it sure does.   Tone wheel lines up in the same spot perfectly.    
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Something I meant to say when we were chatting the other night about having an open trailer floor being great to work on a car, but you've never used the feature... It's a great place to park a car after doing suspension component changes, and do the tightening of all the bushes with the car sitting at full ride height. Especially when you don't have a 4 post hoist!
    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
×
×
  • Create New...