Jump to content
SAU Community

Recommended Posts

got a hks type s oil cooler kit (sandwhich type) to suit all RB engines. its used and comes with all necessary fittings. selling as some bills have come up but otherwise i wouldve kept it... looking for a quick sale at $500+delivery. these units retail for about $900 or so.

PRICE DROP now $400 FIRM.

located in sydney..

post-17892-1152200818.jpg

Link to comment
https://www.sau.com.au/forums/topic/125129-hks-type-s-oil-cooler-kit/
Share on other sites

from this site: http://www.importscene.com.au/prod542.htm

HKS Universal Oil Cooler - Type S

UNIVERSAL OIL COOLER KIT

There are two different types of oil cooler system. R (Replacement) TYPE is to relocate oil filter. Attachment of S (Sandwich) TYPE is inserted between engine block and oil filter.

Thermostat controls oil temperature

HKS Oil Cooler uses high efficient core. Thus it has thermostat to prevent oil viscosity friction due to over-cool (Except some vehicles). The thermostat responds quick to temperature. When oil temperature is not enough warm, it bypasses core to warm up engine quickly. If oil temperature exceeds thermostat working temperature, it flows oil to core to cool.

Thermostat closing start temperature 70?(±3?)

Thermostat closing complete temperature 80?(±3?)

* Applicable Meter fitting Oil Temp. Fitting M10xP1.0(R TYPE only), M12xP1.25 Oil Pressure Fitting PT1/8

Thermostat has relief function for safety

In case oil pressure has been unusually increased like core is damaged or oil line is stopped, oil is relieved from thermostat and it bypasses core to prevent engine failure and rupture of oil line.

Stainless mesh hose oil line for durability.

To connect surely, US Aeroquip stainless mesh hose and fitting, which are good function, durability and looking proofed by military usage, are used.

S-TYPE SPECIFIC INFORMATION

Attachment of HKS OIL COOLER S TYPE is inserted between oil filter and engine block. It is a high quality performance product. Mesh hose and fitting are Aeroquip. The attachment has sensor holes for oil temperature and pressure gauge.

* It does not relocate oil filter.

- Adopter thermo : M12xP1.25 (2 holes), PT1/8(1 hole)

UNIVERSAL OIL COOLER KIT S TYPE

Length of hose 3m

197×158.8×32, 12 rows (No.129)

- Core has been changed to popular size. (No. 012 --> No. 129)

* It is possible to install to vehicles which thread size of stock oil filter is 3/4-16UNF or M20×P=1.5. (Excluding some vehicles.)

sorry dunno to much about the specifics hope that helps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even welded diff, in a dead straight line is quiet. It's what's in my R33, and you only notice it is welded when attempting to turn.   This to me sounds like there is play somewhere. But I'm not sure where I'd look to be honest.   OP: are your tyres the same size left to right? Can you check what the markings on the rear left and rear right tyre are, and then how much tread is on each tyre?
    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
×
×
  • Create New...