Jump to content
SAU Community

Recommended Posts

I was just wondering how the stock gtr bov's are plumbed. are they located on the side of the intercooler near the throttle body or the other side near the turbos. Also do they resirculate one to each turbo or how is it set up? I am wondering cause I am plumbing BOVs for my swap in an s13 and it did not come with any ic or piping. Thanks for your help guys any and all info will be usefull.

Link to comment
https://www.sau.com.au/forums/topic/125796-stock-gtr-bov-plumbing/
Share on other sites

GTR has 2 bovs.

They are mounted on a single larger pipe (bit smaller than the intercooler piping) and are located in the drivers side kinda in the front air dam..

So if you are looking at a GTR front on, you will see the big space in the middle for the intercooler and the smaller space on your left (drivers side when looking front on) is where you will see the bovs.

The plumbing for it is like a Y pipe. 2 hoses join to become one and the one pipe goes all the way over to the intake pipe which is from the air box to the turbo’s.

Why it has 2 bovs?

Not sure.

I doubt it has anything to do with 2 turbo’s.

My guess is it has something to do with the fact that the rb26 has individual throttles.

It seems people who change the bovs to atmo ones on rb26’s have all sorts of problem with idle and turbo surge etc..

Thanks. are they plumbed back before or after the mafs (afms)?

"after" - by 'after', I mean 'closer to the engine'. Air that's re-circulated is not supposed to be measured twice.

Just plumb your system back somewhere between your AFMs and the turbo inlet.

If you take a look at a diagram or pull a GT-R's inlet pipework to bits you'll see where the re-circulation pipe rejoins

the system. When you get all the bits onto the bench(es) you will not _believe_ that they all go back in that little tiny space :))

This is possibly why the pipework was not included :yes:

The valves are in parallel; so I'd guess that there are two simply to allow for more airflow when they are open while

keeping the response characteristics of a single smaller valve. They _may_ be sprung differently (I've never

tested) but they look identical.

Regards,

Saliya

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...