Jump to content
SAU Community

Recommended Posts

broke my drag racing virginity last night at Willowbank, QLD

car:

r32 gtst

rb20det automatic

155rwkw

time:

14.714

98mph

60' 2.503

The 2 things that were hurting me:

takeoff with the auto and rb25 turbo was hard. stomped on accelerator and brake and pulled up handbrake, but couldn't build positive manifold pressure as it has an rb25 turbo that's slightly too big to get boost at that load

i run out of power about 6000rpm as it gets too rich, so the auto changing at 7500rpm wasn't helping.. would ideally have changed at 6500rpm of there abouts

any ideas to improve?

I would have thought that with a 60' time of 2.2ish i could get mt ET down to 14.4ish with just that?

cheers,

Warren

Link to comment
https://www.sau.com.au/forums/topic/126090-first-time-at-the-drags/
Share on other sites

I would say thats about right hey...

The 60 footer is pretty ghey but there is not much you can do with the factory stall on autos unless you get it restalled...

I would probably try and do kinda a line lock and before it starts to build up decent positive pressure in the inlet release the brake and kinda skid off the mark...may sound stupid, but i would give it a go...

shifting manually doesn't make a difference as it still changes are redline..

when you put your foot down, it activates the "power" function automatically and it can't be turned off when you're flat out...

and as i have an rb25 turbo, the exhaust wheel is slightly too big to make boost when stalling the auto at 1800rpm.. I would say its about -2psi (relative to atmospheric) at that load, so its quite close to making positive manifold pressure, but not quite there

like I said in the other one 98 mph is good for a high 13 with a better 60ft and a few decent shifts.

If you are holding consistant revs to stall you might find that you can't get positive boost. To hold the rpm at that level there isn't engough load to have the throttle opening enough for boost.

So perhaps just stomping the accellerator down is a better approach and forgetting the handbrake thing for now since you don't have a enough stall speed. having a snick of wheel spin off the line will get the turbo into boost otherwise you are bogging down.

shifting manually doesn't make a difference as it still changes are redline..

when you put your foot down, it activates the "power" function automatically and it can't be turned off when you're flat out...

and as i have an rb25 turbo, the exhaust wheel is slightly too big to make boost when stalling the auto at 1800rpm.. I would say its about -2psi (relative to atmospheric) at that load, so its quite close to making positive manifold pressure, but not quite there

could you just ease up off the pedal in a gear to make it down shift and then floor it again. if the previous rpm was around 80%+ then the car should just hold the next gear without down shifting.

shifting manually doesn't make a difference as it still changes are redline..

when you put your foot down, it activates the "power" function automatically and it can't be turned off when you're flat out...

and as i have an rb25 turbo, the exhaust wheel is slightly too big to make boost when stalling the auto at 1800rpm.. I would say its about -2psi (relative to atmospheric) at that load, so its quite close to making positive manifold pressure, but not quite there

If you can make a little boost you will find the stall speed goes up, if you can get the stall rpm up you will make more boost (Catch 22).

What you need is a bit more ignition advance around 1800 rpm.

What are you using to tune it with? SAFC? Rechip? Power FC?

If you have an SAFC, try leaning it out around 1,800 rpm. That will give it some ignition advance at the same time. If you then get some pre-ignition with 98 ron, try Shell Optimax Extreme 100 ron. That will avoid the pre-ignition problem.

Once you get some boost (torque) you will find the torque converter stall rpm will go up. Even as little as 100 rpm might be enough to break the circle.

:( cheers :pirate:

Edited by Sydneykid

gary - stock ECU (i know, i know, its my next engine mod.. but goign the shift kit first)

don't have the snow mode button, only the "hold" which i believe is the same thing - will try the 2nd-gear-takeoff-then-into-first method before i go next

neutral dump? i'm not an idiot...

no point buying smaller tyres as it defeats the purpose of my drive in, drive away approach

oh, and i ran it on optimax extreme, like i do everyday :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...