Jump to content
SAU Community

How To Install?

Trooper

By Trooper,
in Car Audio & Electrical

 Share

Recommended Posts

Trooper Experienced

Trooper

Posted
Posted

Ive just bought a capacitor for my new setup (Soundstream 5 Farad cap) and just wondering if there any "Dont's" associated with the install? As i understand they can be a bit nasty if 'accidentally' discharged.

I am drawing up a basic wiring diagram and just wanting to confirm exactly what happens with the capacitor is this right?

Power wire from battery to capacitor

Then continue to the power input on the amp

With the earth does the amp get earthed via the cap or do I run an earth for the amp and a second one for the cap? or is the cap not earthed seperately?

Any advice would be great

This is what I have bought so far

Pioneer Splits (Already installed)

P4004 Rockford amp

P3 10' Rockford sub

Soundstream 5farad capacitor

Later on I will buy a monoblock and run a second P3 sub and also move the pioneer speakers into the rear of the car and buy some decent focal splits for the front.

I will have my old sub and amp to sell (less than a year old) not sure what they are worth

The sub is a kicker 10' dual voice coil sub (the silver shiny patterned cone one)

and the amp is coustic 4 ch.

I cant remember how much I paid for these, any ideas what I should ask for when I sell them?

Link to comment
https://www.sau.com.au/forums/topic/126148-how-to-install/
Share on other sites
Freddy Kruger Mentor

Freddy Kruger

Posted
Posted

you got a 5 farad capacitor for A 10 inch sub? how much you pay?

dont get me started on capacitors. i ran a 12" with 950wrms thru it and i hammered it everytime i drove the car... the most modification i did for the power is re earth the car with a bigger guage cable and bought a better battery (was still 'only' a Bond silver/calcium battery).

never had a flat battery except for one time i left the interior light on over a long weekend.

Link to comment
https://www.sau.com.au/forums/topic/126148-how-to-install/#findComment-2330490
Share on other sites
LiQuid IcE Experienced

LiQuid IcE

Posted
Posted

Iv'e got a positive cable from battery to cap and a negative cable from batter to cap.

and left the amps the way they were, battery to amp, amp grounded to the body.

Essentially it works out to be the same as what your saying... shouldn't matter whether you get the power for the amp from the cap or the battery, its all the same wire.

Im an ameture though :( so get a 2nd opinion...

on the same topic, does the cap help save the battery from going dead that much?? I got it to stop my lights from dimming when the sub thumped.

Link to comment
https://www.sau.com.au/forums/topic/126148-how-to-install/#findComment-2330752
Share on other sites
Medium Dave Proficient

Medium Dave

Posted
Posted

Hey Heath, you are on the money here, power to cap then amp, as for the negative it shouldnt matter if you give it a seperate earth or not. You are also right about an accidental discharge, there is a lot of potential energy stored in them and they are designed to discharge very quickly, hopefully the worst thing that would happen is that it would scare the sh*t out of you :banana: -keep that in mind when you are removing it too, they will stay charged for days after being unhooked from the battery.

Also, they wont stop your battery from going flat as they only store charge that is already there, they can not create power, cheers

Link to comment
https://www.sau.com.au/forums/topic/126148-how-to-install/#findComment-2333302
Share on other sites
Trooper Experienced

Trooper

Posted
  • Author
Posted
Hey Heath, you are on the money here, power to cap then amp, as for the negative it shouldnt matter if you give it a seperate earth or not. You are also right about an accidental discharge, there is a lot of potential energy stored in them and they are designed to discharge very quickly, hopefully the worst thing that would happen is that it would scare the sh*t out of you :banana: -keep that in mind when you are removing it too, they will stay charged for days after being unhooked from the battery.

Also, they wont stop your battery from going flat as they only store charge that is already there, they can not create power, cheers

Thanks for that mate

I think I will run a common earth for battery and cap then. I remember playing with very little caps at school playing pranks on people with them, and the TINY ones still hurt, this is a lot bigger so i suppose the hurt will be a lot bigger too.

Now it is just a case of watching the tracking updates on the net and waiting for the postman!!

Link to comment
https://www.sau.com.au/forums/topic/126148-how-to-install/#findComment-2333522
Share on other sites
frx026 Proficient

frx026

Posted
Posted
Paid a few hundred for it, looking to upgrade later so I thought I would be better off doing things properly the first time -cheaper in th long run.

I get a flat battery all of the time, dont think the cap will help that (i think its the alarm draining my battery) thinking about possibly installing a second battery in parallel. I do get a few blown headlights though due to the constant dimming with the base. Hopefully that will stop now

You are 100% right, any cap will not help your battery from running flat. It wont help with your headlights dimming etc.

Honestly, if you are having problems with your lights dimming to the point where the hedlights fail due to lack of voltage you need to

- upgrade your alternator

- upgrade your regulator

- upgrade all the earths from your main devices, engine, battery, chasis.

If you do decide to put in a second battery without doing these you will just run that battery down to.

As for your alarm draining your battery, it is possible, but highly unlikely, an alarm at rest ( not going off) draws very little current and wont make your car go flat. Check to see if your boot light is staying on or some other device is constantly active. This will drain the battery.

Link to comment
https://www.sau.com.au/forums/topic/126148-how-to-install/#findComment-2335434
Share on other sites
  • 2 weeks later...
VB- Veteran

VB-

Posted
Posted

the main 'dont' when it comes to capacitors is buying/using/installing one in the first place. while i haven't much experience with these, i believe what the pro's write. take a look on car audio australia as to what they say about caps.. a general consesis is 'uterly useless'

if u want to stop lights dimming, upgrade all earths, get a better battery, upgrade charge wire from alternator to battery, make sure all ground/connections are clean with good contact

Link to comment
https://www.sau.com.au/forums/topic/126148-how-to-install/#findComment-2360246
Share on other sites
Trooper Experienced

Trooper

Posted
  • Author
Posted

Thanks for the advice mate... I might sell the cap (i bought one for my bro too)

Any idea what they are worth? ive seen 1farad ones selling for like $400and ive got a 5 farad one (soundstream too). My brother was told they are worth about $1000 at autobahn :S crazy (he is the one that bought it for me actually)

If i can sell it for enough $ it should pay for a new alternator/wiring etc

Good news re battery drain though....it WAS the alarm after all

Damn idiots installed it incorrectly to begin with :happy:

All fixed for under $100 at an auto elec

Link to comment
https://www.sau.com.au/forums/topic/126148-how-to-install/#findComment-2371504
Share on other sites
Kinks Grand Master

Kinks

Posted
Posted
ive seen 1farad ones selling for like $400

Wow, people are getting ripped the hell off.

A small auxiliary battery would shit all over a capacitor for energy storage. The pulse current of a cap might be a bit higher but if you're drawing that much current you won't have much hearing left soon.

Link to comment
https://www.sau.com.au/forums/topic/126148-how-to-install/#findComment-2374309
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ben_D
      Wanted to buy R200 longnose LSD 3.9 ratio

      By Ben_D · Posted

      Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Ben_D
      Back for more after 18 years - and where are the longnose R200 LSDs?

      By Ben_D · Posted

      Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • sonicii
      G35 Control arm and Compression Rods into a V35 Skyline.

      By sonicii · Posted

      Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
×
×
  • Create New...