Jump to content
SAU Community

Recommended Posts

I just had discussion's with my mechanic where i told him i wanted a 10w 40 redline rating in the gtr! What it had!

I find out he couldnt get it and has put in a 15 w 50 version ... NOw i am paranoid about this because of the complex componnents in the 26's head

. He made a statement that i will have better oil pressure because it reads low on the guage ...

I just belive the Gauge is intermitent . and waiting to install a better device..

Now we are talking $130 worth of oil here and i just wanted opinions if i should re change or run it until next change ... What could happen ? Topend ware?

to me the motor is very Quiet and strong with 140,000 km's .. I do know it had its magor service at 100000 belt (Etc)

What do you think ?

Link to comment
https://www.sau.com.au/forums/topic/126182-wrong-expensive-oil-put-in-redline/
Share on other sites

Bascisally, nissan recommend a 7.5 w 30.

Thinner cold viscosity helps it to lubricate the engine quicker when it's been sitting e.g. overnight. Most of the wear to an engine occurs during start up.

The warm viscosity isn't as important. But a thicker oil requires more heat to break it down at high temperatures.

Yeah its pissed me off a bit ..... I will do a short change 2000

To be hounest i just want the car outta his shop ...

He came across as knowing a bit but as you go along you realise that he is learning as he is going ... This is the last mechanic to ever touch this Car in the town of Albury Wodonga .. I have learnt so so the hard way ....

it is mega Cold here in winter so it makes no sense again!

Thanks

Ish!

Yes do your own oil changees and use a nice PureOne or genuine filter.

The 15w50 will be fine, do remember nissan recommend 7.5w30 for a new motor with jap conditions being considerably cooler than ours.

I'd leave it in for the whole 5000k. No need to drop it. :(

As your spending so much on oil consider have an oil analysis done on it after 5k, then drop in the 10w40 do 5k on it and give that an oil analysis too. Will indicate which is better suited to the driving and condition of your motor.

Can you even get 20W50 in a good synthetic oil?

I've only seen 20W50 in cheap minerals oil, good for old XF Falcons and the like.

Have a go yourself, you couldnt, f**k up more then your mechanic already has. Didn't even do as you asked.

it was a case of me swallowing my temper to get my car outta there!

Redline make it in that Viscos For there Big ol Gappy motors in the States .

No, don't dump the oil. Redline being polyol ester base have pretty good cold pour point, i would say used it to 10k before you dump it.

The oil you have will be fine, but if you want to have an argument with the mechanic that's up to you. One-off oil analysis falls into the same category as cryogenic treatment......a complete waste of time and money.

Not a complete waste of time.

Early notification of fuel, water air filter problems... And gives you an indication of the oils VI over your change period.

With regards to wear yes it can be a waste of time.

SteveL it was way more things than just the wrong oil that caused tension.

I simply found out he had BS'd me on a few points > this Was not the Point of the Thread

I Asked here about the viscos because i didnt know and wanted to get the info form people that did, incase of Damage.

Regarding the OIL analysis I just found it Personaly interesting to see what becomes of the oil after a term, not to argue.

Its all good now ... Cars home ,it has its proper oil and the Vl Commie has its own batch now too, Nothing Wasted!

thanks everyone.

Edited by ishh

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...