Jump to content
SAU Community

Has Anyone Actually Removed Their Front Drive Shaft

japhearse
 Share

Recommended Posts

japhearse Enthusiast

japhearse

Posted
Posted

Hi i was under my stag today checking how to pull out the front drive shaft as its going for a dyno check tomorrow, and to me it looks like if the the tranny seals on shaft and if its removed the atf is going to piss out of box. So i was wondering has anyone actually removed their front shaft to prove me wrong

CruiseLiner Mentor

CruiseLiner

Posted
Posted
Hi i was under my stag today checking how to pull out the front drive shaft as its going for a dyno check tomorrow, and to me it looks like if the the tranny seals on shaft and if its removed the atf is going to piss out of box. So i was wondering has anyone actually removed their front shaft to prove me wrong

hey mate u can pull it out and oil wont come out of the box as its totally sealed inside where the shaft goes into the transfer case.

all u need is 2 x 12mm spanners im pretty sure to get it off. just remove the 4 bolts from the sump end of the shaft and slide it out the transfer case and its done :banana:

i been running around in 2wd without the shaft in for ages now without a problem and i know 100% that its sealed in the transfer case shaft hole :) even a big workshop told me it wasnt sealed until i checked and it infact is a sealed unit as we have had the transfer case stripped down in our garage into about 20 pieces checking the clutch packs.

hope it makes sense mate

Brad

Spammeoff Contributor

Spammeoff

Posted
Posted

I've had mine out for a couple of weeks with no probs at all. I found I had to loosen off a cable going to the auto that real close to the shaft to get it out. And I found the nuts on the flange at the front were real tight, you need reasonable access and good spanners or you might round them off.

I covered up the hole in the gearbox with duct tape so no road grime got in there. Tape hadn't moved after a few weeks. Pretty easy to get overly loose in rwd mode if the auto kicks down mid-corner and you weren't ready...... :banana:

japhearse Enthusiast

japhearse

Posted
  • Author
Posted

Left the removal of the shaft to daltons, decided it was to hard to do it at home. when he put it up on the hoist he was straight back to tell me that he if pulls it out oil will piss out he also took a bit of coaxing to try it, but it worked and and now its a 2 wheel drive till i get the uni replaced or a replacement shaft its stuffed unfortunately :wave:

CruiseLiner Mentor

CruiseLiner

Posted
Posted
on this topic... not that anyone would, but could you remove the rear driveshaft and make a front wheel drive?

no u couldnt as its not fulltime 4wd like a wrx so its rwd 99% of the time. and the transfer case clutches are tiny and only made to work for minimal amounts of time before they will burn out.

why would u want to anyways? :whistling:

cheers

Brad

munchstagea Mentor

munchstagea

Posted
Posted
Left the removal of the shaft to daltons, decided it was to hard to do it at home. when he put it up on the hoist he was straight back to tell me that he if pulls it out oil will piss out he also took a bit of coaxing to try it, but it worked and and now its a 2 wheel drive till i get the uni replaced or a replacement shaft its stuffed unfortunately :P

Nice work Darrin, good to see you are educating Dalton's on working with Stagea's. I am in Aireys Inlet and would be going to Dalton's for anything dyno related, so how did it go, what did they do and how much did they charge you?

I dropped in there when I first got mine and asked them about what turned out to be a turbo manifold gasket and they were right on the money and very approachable.

Cheers

Luke

japhearse Enthusiast

japhearse

Posted
  • Author
Posted

Hi Only really went on the dyno to check the air fuel ratio, just was expecting about 120rwk. We both ended up with a big shock when the first 2 runs produced 148rwk then 149rwk with the afr 14.5 dropping to about 12.5 on boost.

After a chat he went and checked the dyno was set correct and did a 3rd run which came to a total of 152.8rwk on stock boost and as far as i know stock engine pretty happy with that, but now trying to find out why.

definatly happy with chris dalton hes a rotary fan, but knows his way around the skylines, shaft removal and 3 dyno runs $99 pity he didnt find any faults though, hoping for a cure for the petrol blues.

munchstagea Mentor

munchstagea

Posted
Posted

Nice power figures (every dyno is different before the knockers come knocking, we all know that!)

I'd say your fuel usage might have something to do with the amount of power it is making... But yes the question is why is it making that much? You find out what the deal is let us know ok? Any mods?

Cheers

Luke

japhearse Enthusiast

japhearse

Posted
  • Author
Posted

hi luke The only mod its got that i know of is the little air freshener that my misses stuck on the center air vent

must say its nice to see there is another stagea owner down this way id recommend daltons at least he nows what they look like and how to pull the shaft out thats more than any of the others

Spammeoff Contributor

Spammeoff

Posted
Posted

If your AF is really 12.5 on boost, even standard boost, then its a lot leaner than factory, which would go some way to explaining the power. I'm sure you'd notice if it had a interceptor, so maybe its got a chipped ECU? Someone could have fitted a generic lean-out/advance chip, they're pretty common for popular engines like RB25det in NZ anyway. I'm under the impression for a bit of a 'general' tune the chip guys can do not a bad job.

Spammeoff Contributor

Spammeoff

Posted
Posted

It'd work, but of course you'd get richer running across all loads and revs which is a bit of a compromise. For the cost of a adjustable fuel regulator you can pretty much buy the Jaycar digital fuel adjuster and hand controller and get lots of adjustment, and just where you need it. Although with standard boost, and premium fuel, I'd have thought 12.5:1 would be a good ratio? Maybe not on a 30deg day I guess.

STAGE-A Rising Star

STAGE-A

Posted
Posted (edited)

nice figures mate!!

just a question tho how do RWKW's compare to AWKW's? .. was just reading Alex's post on the GCG group buy and he mentioned he got 160AWKW with the hi-flow (untuned) compared to the 115-120AWKW's standard. Compared with your 150RWKW fully stock (minus the air freshener :D .

Does anyone have a formula or anything?

Edited by STAGE-A

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...