Jump to content
SAU Community

Speedo

burnsie

By burnsie,
in General Maintenance

 Share

Recommended Posts

blind_elk Grand Master

blind_elk

Posted
Posted

(not sure what Joe was smoking when he put up his response - or am I missing something?)

It seems you have a R32. If so, it is likely the end that fits into the back of the speedo has sheared.

Has the odometer also stopped working?

Link to comment
https://www.sau.com.au/forums/topic/127142-speedo/#findComment-2352371
Share on other sites
[WLDCRD] Mentor

[WLDCRD]

Posted
Posted

yeah just pull out that dash assembly and you will see the speedo cable. It should have a plastic pin thing that sits on a spring that goes in that cable. Make sure the pin base (as the pin part itself moves freely) is pushed back but the pin is pulled out. You will understand what i am talking about when you see it. Use a small flathead screwdriver to push the base back and a small needlenose plier to pry out the pin. Carefully put the dash back in. DOnt put it all back together as you will want to go for a test drive to see if it moves otherwise you gotta take it all out again. Hope that helps.

Link to comment
https://www.sau.com.au/forums/topic/127142-speedo/#findComment-2352726
Share on other sites
SECURITY Grand Master

SECURITY

Posted
Posted
(not sure what Joe was smoking when he put up his response - or am I missing something?)

It seems you have a R32. If so, it is likely the end that fits into the back of the speedo has sheared.

Has the odometer also stopped working?

what was wrong with my response?

in my experience, every time someones speedo has stopped it has ALWAYS been the speedo cable in the engine bay.

Link to comment
https://www.sau.com.au/forums/topic/127142-speedo/#findComment-2352826
Share on other sites
burnsie Veteran

burnsie

Posted
  • Author
Posted
' date='24 Jul 2006, 05:08 PM' post='2352726']

yeah just pull out that dash assembly and you will see the speedo cable. It should have a plastic pin thing that sits on a spring that goes in that cable. Make sure the pin base (as the pin part itself moves freely) is pushed back but the pin is pulled out. You will understand what i am talking about when you see it. Use a small flathead screwdriver to push the base back and a small needlenose plier to pry out the pin. Carefully put the dash back in. DOnt put it all back together as you will want to go for a test drive to see if it moves otherwise you gotta take it all out again. Hope that helps.

thanx heaps mate ill let you know how i go hope it works for me

Link to comment
https://www.sau.com.au/forums/topic/127142-speedo/#findComment-2353611
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...