Jump to content
SAU Community

Remapping A Stock Rb25det Ecu.

RB SANDY

By RB SANDY,
in Engines & Forced Induction

 Share

Recommended Posts

The Dan Grand Master

The Dan

Posted
Posted
Hi guys do you know of any one in Melbourne that remaps the stock rb25det ecu because the R&R in kicking in and using a lot of fuel and I don’t have the $$$$$ for a power fc

As far as I know the Rb25DET ECU cannot be remapped. Although you can call DR DRIFT on 0425818755. He does the remapping all over Australia.

RB SANDY Rising Star

RB SANDY

Posted
  • Author
Posted

Buy the way my car is a r32 gtst with a rb25det s1 motor in it.

To get rid of the R&R you could cut the sensor out of the afm and put it in a 90mm pipe instead of a 80mm pipe.

It could work just a thought, because the ecu thinks the boost is set a 10psi instead of 12. at 10psi the a/f is still rich so it might be for 12.

Tangles Grand Master

Tangles

Posted
Posted

get a SAFC, either series 1 (~$50 used) or series 2 (~$200 used or $350 for new)

install it, make sure every bolt-on mod you're doing is on the car - and dyno tune.

more power and save $ in the long run.

aphid Proficient

aphid

Posted
Posted

hey,

i was going down this path with Dr Drift, he put the 32 ecu into my car and got it working on one of his stockish maps. never got around to tuning though, the contact just sort of broke off as he is a very busy man and i ended up getting a power fc instead. the 33 ecu uses a different chip which has the actual program embedded in the chip itself, which can't be wrewritten too and thus a new one must be installed which is expensive (this is the reason he gave to me). anyway as they say get in contact with Sam, he's a very smart bloke.

cheers,

mark.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Duncan
      What brakes on R34 GTT(Europe)

      By Duncan · Posted

      Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...