Jump to content
SAU Community

R32 Gtr 4wd

ali-turko
 Share

Recommended Posts

ali-turko Grand Master

ali-turko

Posted
Posted

hey guys tryed searching and read the other thread bout this but i just got my car back from the panel beaters and my 4wd isnt working also the abs isnt working! the panel beat pulled all dis shit of my engine bay so something might not be plugged in, iv checked all the fuses all that sort of stuff...

dose anyone have any suggestions?? and i don want to take it back to the panelbeaters coz his a dogey F@#k and im ready to kill him!!

canyone plz help me

Link to comment
https://www.sau.com.au/forums/topic/127286-r32-gtr-4wd/
Share on other sites
Topaz Grand Master

Topaz

Posted
Posted

Are you going off their word or do you know for sure these are not working?! Simple test for 4WD is under hard acceleration, check the torque guage for movement.

ABS makes the pedal feel 'squishy' and it seems to keep going to the floor (not all the way though) when pressed hard. Try this while the car is on but not moving. It may seem very 'free' on first start up and that theres air in the system.

Link to comment
https://www.sau.com.au/forums/topic/127286-r32-gtr-4wd/#findComment-2350526
Share on other sites
ali-turko Grand Master

ali-turko

Posted
  • Author
Posted

iv checked the fuse in the cabin and are u torking bout the 4wd computer on the pacel shelf coz iv checked them as well, and i no theres no 4wd coz i get wheels spinning very easy, also i noticed today i can hear noise from the abs unit in the engine bay wen i turn the ignition, as the fuel pump starts up its start making smililar noises as the fuel pump!!

also i noticed the hicas light flashs aswell wen ignition on but when i start the car it goes away

Link to comment
https://www.sau.com.au/forums/topic/127286-r32-gtr-4wd/#findComment-2350879
Share on other sites
giant Mentor

giant

Posted
Posted
iv checked the fuse in the cabin and are u torking bout the 4wd computer on the pacel shelf coz iv checked them as well, and i no theres no 4wd coz i get wheels spinning very easy, also i noticed today i can hear noise from the abs unit in the engine bay wen i turn the ignition, as the fuel pump starts up its start making smililar noises as the fuel pump!!

also i noticed the hicas light flashs aswell wen ignition on but when i start the car it goes away

there is a relay in the boot at the back l/h/s , if that is disconnected the abs will make a noise and you will have no 4wd.

hope this helps

russ

Link to comment
https://www.sau.com.au/forums/topic/127286-r32-gtr-4wd/#findComment-2352155
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...