Jump to content
SAU Community

Help Needed Epa Test Troubles

NVMYTG

By NVMYTG,
in General Maintenance

 Share

Recommended Posts

NVMYTG Contributor

NVMYTG

Posted
Posted (edited)

my r33 gtst needs to pass an EPA test and to do so i need to have standard boost control parts running. at the moment i have a duel stage boost controller and it runs fine with the duel stage. when i put the vac lines to the standard controller it overboosts. can someone tell me what vac lines need to go where? also i have made sure the plug that comes from the standard controller is plugged in and i have even tried another one from a mates car. could the wiring for the standard controller be used for the aftermarket unit? if so what should i be testing for with the multi meter? the after market controller has an earth wire and a wire running through the firewall and i cant see if the wire from the standard plug has been cut as it dissapears into a loom. any help would be much appreciated. thanks, brad (also my car has a standard turbo,FMIC and at the moment the airbox is fitted and i have checked for vaccum leaks)

Edited by NVMYTG
Link to comment
https://www.sau.com.au/forums/topic/127617-help-needed-epa-test-troubles/
Share on other sites
RANDY Veteran

RANDY

Posted
Posted

You won't need a multimeter... the standard solanoid should give 5psi if it's not working properly, and 7psi if it is.

I suggest that your plumbing is not quite right... from the intake pipe down the bottom, the pipe should come into the bottom of the solanoid (I think.. if not, switch them around), and then the top one goes to your wastegate actuator.

NVMYTG Contributor

NVMYTG

Posted
  • Author
Posted

i treid the lines both ways but i was a little worried id do some damage can anybody confirm which way they are supposed to go? also id like to know what im looking for with a multimeter with the wires coming from the solinoid as i said before i tried the vac lines both ways and i even tried another solinoid from my mates car which i know works.

Mick Mentor

Mick

Posted
Posted

from memory one of the lines was running to a T peice, also one line had a little restrictor in it, if thats not in the right place that may cause your problem.

Let me work out what needs to go where cos im in the exact same boat as you, i have a dual stage boost controller installed and i need to put the standard one back on so i can get it trough RoadWorthy.

Mick Mentor

Mick

Posted
Posted

Ok here is what i worked out on how to properly install the stock boost controller.

First off there is a hose from the actuator goin to a T peice, its only short and it has a yellow band on it because it has a brass restrictor in it.

From the T peice it goes to the BOV retuirn pipe.

Then from the T peice it goes to the bottom of the boost controller.

The last is a straight hose goin from the intercoller pipe to the top of the boost controller.

Can someone please confirm this for me, i just want to be %100 sure.

I mainly want to know if the restrictor is in the short hose coming off the actuator and goin to the T peice.

I hjope this helps, im %99 sure this is right which i would love someone to confirm this all for me ..

mad082 Grand Master

mad082

Posted
Posted (edited)

no thats wrong.

(if you have a front mount there will be a hose from the bov pressure line (the vacuum hose that opens the bov) instead of the intercooler pipe)

there should be hose hose from an intercooler pipe. this goes to a T piece. from the T piece there should be 1 hose going to the wastegate, and 1 to the lower hose of the factory solenoid. the top hose of the solenoid should go back to the intake (bov plumback pipe).

Edited by mad082
Mick Mentor

Mick

Posted
Posted

Ok this is straight from the Nissan Fast program, so thjere is no disputing it.

Top of the boost controller goes straight to the wastegate.

The bottom goes to the T peice.

One side of the T peice goes straight to the intercooler pipe.

The other side of the T peice goes straight to the BOV return plumbing.

Thats it, 100%..

Mick Mentor

Mick

Posted
Posted (edited)

I also found a picture in another thread showing the stock setup i described.

The restrictor is in the short hose goin from the intercooler pipe to the T peice, make sure you have the restrictor in place.

http://www.skylinesaustralia.com/forums/in...st&id=45802

Edited by Mick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Tein Circuit Master- rebuild worth it?

      By MBS206 · Posted

      If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • MBS206
      Best place to order Authetic R32 Parts in Japan

      By MBS206 · Posted

      Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
    • MBS206
      NC MX5

      By MBS206 · Posted

      Murphy strikes again! Nothing at all would have gone wrong if you had the tool kit in the car! You'd have just found the clamp loose the next time you went to touch it...
    • MBS206
      Blue slip

      By MBS206 · Posted

      I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
×
×
  • Create New...