Jump to content
SAU Community

Recommended Posts

Hi!

Ever since Ive had the car the steering is very tight. Takes alot of effort to turn. Its like I have no power steering (But I do, ive checked the fluids all fine).

When I turn the wheel it requires alot of force to actually turn it.

What may be the reason for this?

And dont say its coz im weak blach blah blach. Everyone who drives my car says its tight.

Could it be Hicas? or something? :P

Link to comment
https://www.sau.com.au/forums/topic/128382-steering-very-tight/
Share on other sites

Firstly, check your belt is tight, then make sure your pump is actually turning and then do the diagnostic check ( very cool thuing to see :laugh: ). BTW, if your power steering pump stops working all together, you'll know about it fast !! Maybe try replacing the power steering fluid and see how that goes.

If the diagnostics show up with nothing and you're at a loss, PM me, I still might have one ace up my sleeve to help you out :wub:

Try the steering with the engine not running, parked up, then WITH it running. There should be a MASSIVE reduction in effort with the engine running. If there is NO difference the PAS has failed, either the rack is faulty, the pump, its drive belt, or just maybe a blocked fluid reservoir gauze or a crimped PAS hose. If the car has taken a blow to the front wheels it is possible to burst the rack seals or for the pressure relef valve in the pump to be forced wide open and stick, or other pump internal faults to be created.

If there is a slight difference suspect eithe the pressure relief bvalve in the pump, a goosed pump, or a goosed rack, or again, a crimped hose.

Rack faults are USUALYY combined with fluid leaks. If you narrow it down to the pump or the rack try and borrow a known good pump and try that, it's quicker and easier to change than the rack, although neither are exactly tricky!

Although my vehicle is a 180SX, i use Skyline steering rack and piping as i run an RB25, I have a similar problem with mine but i have a solution.

My problem is the same as yours. My rack is from a 4 wheel steer model, the system runs a "booster" solinoid for when the engine is running at low rpm i.e parking. to assist with the low system pressure. I performed a check of my system and my car doesn't run the solinoid "booster".

The fix in my case is to use a rack from an S13. Not sure if your rear steer has been disabled, or removed altogether, but this may help you narrow it down.

Hope it helps

Edited by Simonster

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...