Jump to content
SAU Community

Recommended Posts

Hey peeps

Have these bits for sale, all came out of an r32 gtst (bar the rb25 actuator)

- standard rb20 turbo with a bearing noise $80 (includes oil line and rb20 elbow)

- rb20 actuator $30

- rb25 actuator $20

- rb20 injectors x6 (in bags) $20 each or $80 for the lot

- rb20 afm $80

- rb20 fuel pump $40

- rb20 fuel pressure regulator $20

- rb20 manifold heat shield $20

- rb20 turbo heat shield $20

- rb20 coils $30 each or $100 for the lot

- rb20 stater motor $30

- r32 speedo dash surround $20

- r32 cooler + air guide/some piping $15 (postage wouln't be cheap to over east)

Pictures are attached below

Buyer to pay registered post fee or COD delivery costs.

Located in Perth, happy to send anywhere.

Please email [email protected] or pm me if interested!

Thanks all

post-7888-1154840978.jpg

post-7888-1154840987.jpg

post-7888-1154841022.jpg

Edited by jazza08
Link to comment
https://www.sau.com.au/forums/topic/129031-rb20-parts/
Share on other sites

The turbo boost's fine but makes a noise through the bearing, if you wanted somethin to get your outta trouble it would work as niether exhaust nor compressor wheel has much play on it, but id suggest a rebuild as no noise is a good one? lol.. gcg-hiflow etc :P

Edited by jazza08
Link to comment
https://www.sau.com.au/forums/topic/129031-rb20-parts/#findComment-2408117
Share on other sites

  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...