Jump to content
SAU Community

Gb: Brand New Z32 Afm's - $330.00 Each


Recommended Posts

  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

Blitz, this may seem like a sil question, but is there any difference between the genuine Bosch item and a Nismo one?

The Bosch/Nissan Z32 AFM's are 80mm,where the Nismo/Tomei units are smaller in physical size, but still have increased voltage capabilities over the standard AFM - They are also significantly more expensive and tuners I have spoken to seem to prefer the standard type 80mm Z32 over the Nismo/Tomei type units.

Hope this helps

Payment made and email sent to Darron

Alan

Hi Alan, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581246)

Cheers,

Nick

Received the AFM yesterday, damn quick delivery :ninja: Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Your very welcome mate :ninja:

Payment made and email sent to Darron :ninja:

Gday Matt, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581247)

Cheers,

Nick

CAn you hook these units up to a stock RB20DET and see a difference or will it be just a waste of time until i get my Power FC?

Thanks guys

You will need to wait until you have a Power FC :D

Woohoo! Received mine today! thanks mate! :D

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Received the AFM yesterday, damn quick delivery :D Thanks mate.

Anyways anybody know the wire colour codes for a R34GTT e.g which ones signal, batt etc, gonna splice and hook up myself...

Hey AcoustiK, try this thread, might help you a bit! :yes:

http://www.skylinesaustralia.com/forums/in...howtopic=116520

Woohoo! Received mine today! thanks mate! ;)

Also does it matter if on one side of the mesh it's slightly dented? doesn't look too bad might be able to gently move it back in place.

Cheers again!

Hi Dave, glad to hear it arrived safely - The dent in the mesh wont be a problem, in some cases people remove the mesh all together.

Hey Blitz,

Just transfered the funds, and emailed Darron too.

Thanks

Hi Nikki, your payment has been confirmed and is on its way to you via express post (Ref: # SN0581250)

Cheers,

Nick

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...